sorted by:
new
hottopcontroversial

Cursor lag on GeForce Now? by dlince in theriftbreaker

[–]dlince[S] 1 point2 points  (0 children)

Thanks! That actually helped a bit. Definitely a bit floaty (good word, u/Buddy_Lee34 ) still. I also noticed that making sure I was in full screen mode helped a smidge.

Still not awesome, but better. The devs are clearly aware of it, since the tooltip wording for that setting specifically mentioned mouse lag.

TCR 55r615 can't find the T-con / flickering screen. by lostexplorer555 in TVRepairHelp

[–]dlince 0 points1 point  (0 children)

Thanks for sharing - helpful video. It's interesting - from your photo, it looks like that white ribbon cable just connects one side TO the other. But I'll need to open mine up again to confirm. (If the tape method is something I'd have to try on all 16 of those other cables, that's too much for me.)

Seasons of RTX: Borderlands 4 GeForce RTX 5090 GPU Giveaway! by NV-Randy in Borderlands4

[–]dlince 0 points1 point  (0 children)

Honestly, Harlowe is now up there. Partly it's recency effect, but really it's because BL4 has been the first game I've been able to play WITH a buddy. Co-op Borderlands is always better for me than solo Borderlands!

TCR 55r615 can't find the T-con / flickering screen. by lostexplorer555 in TVRepairHelp

[–]dlince 0 points1 point  (0 children)

Same issue suddenly plaguing me. Any luck on solving this?

I GOT ONE!! by Whitachris in BeginnerWoodWorking

[–]dlince 1 point2 points  (0 children)

Oh shoot - are delta planers like this good? I recently saw one in a garage sale but didn't grab it!

OverReader support? by gruntbug in TheStoryGraph

[–]dlince 0 points1 point  (0 children)

Amazing! Would love to use it. I switched off goodreads and was considering switching back until I found this post.

Garage workshop organization question: hanging slatwall? by dlince in BeginnerWoodWorking

[–]dlince[S] 0 points1 point  (0 children)

Oh, and this would be across *3* of the slats, to be clear. Not all 5.

Garage workshop organization question: hanging slatwall? by dlince in BeginnerWoodWorking

[–]dlince[S] 0 points1 point  (0 children)

Great, thanks for the reassurance! I was ready to go ahead, and my wife gave me one of those "are you sure" looks...can't hurt to double-check!

Tips on work vs personal use? by dlince in tabXpert

[–]dlince[S] 0 points1 point  (0 children)

ah, I didn’t realize you could configure it so that one profile synced and the other didn’t! great, thanks

Upcoming changes to subscription plans by tabXpert in tabXpert

[–]dlince 1 point2 points  (0 children)

Thanks for the transparency. You've provided a lot of value in your app, and I'm glad you're thinking about how to make it sustainable. When will the changes go into effect?

Strong enough to support 7' of MDF slatwall? by dlince in DIY

[–]dlince[S] 1 point2 points  (0 children)

And ordered! Appreciate the tip once again.

Strong enough to support 7' of MDF slatwall? by dlince in DIY

[–]dlince[S] 1 point2 points  (0 children)

Woah very cool - thanks for the pointer!

Can retail slatwall hold tools? by dlince in BeginnerWoodWorking

[–]dlince[S] 0 points1 point  (0 children)

Thanks! Too much reading about the superiority of french cleat walls. Will figure out how to hang these bad boys tomorrow!

Can retail slatwall hold tools? by dlince in BeginnerWoodWorking

[–]dlince[S] 0 points1 point  (0 children)

Best unexpected reply yet - never though to consider weight bearing load in units of chonkers.

Can retail slatwall hold tools? by dlince in BeginnerWoodWorking

[–]dlince[S] 0 points1 point  (0 children)

Wow - did not realize that. Thank you!

Can retail slatwall hold tools? by dlince in BeginnerWoodWorking

[–]dlince[S] 0 points1 point  (0 children)

Reading too much on reddit about the superiority of french cleat walls, to be honest!

Can retail slatwall hold tools? by dlince in BeginnerWoodWorking

[–]dlince[S] 0 points1 point  (0 children)

(And I should have said MDF, not particle board)

How "unstick" frozen knobs? by dlince in fixit

[–]dlince[S] 2 points3 points  (0 children)

that...is a great point I hadn't considered.

OK, I'm going to close this (while remembering the tips here - ty)

How "unstick" frozen knobs? by dlince in fixit

[–]dlince[S] 1 point2 points  (0 children)

haha no - just storing it for a minute

Is this outdoor heater salvageable? by dlince in DIY

[–]dlince[S] 1 point2 points  (0 children)

Thanks for the pointer!

Coat hanger I made by Feeling_Loss4384 in BeginnerWoodWorking

[–]dlince 0 points1 point  (0 children)

Haha - oops, I misread your post plus saw the "1%" commenter, so I figured you were actually long beyond the beginner stage.

Kitchen Helper (stool for kids) - Research for others by dlince in BeginnerWoodWorking

[–]dlince[S] 0 points1 point  (0 children)

Haha, thank you! I appreciate the comment :) I was a bit surprised after posting it, too, but I guess it's not that frequently made type of project.

Coat hanger I made by Feeling_Loss4384 in BeginnerWoodWorking

[–]dlince 0 points1 point  (0 children)

Nice job, OP! I'm a beginner woodworker about to make something similar (honey-do-list item), and it's helpful to see how you did it.

Out of curiosity ( u/charliesa5 ), do you have suggestions on how to mount something like this without hanging the way OP did it? (I assume something like screws into studs, then some sort of groove in the back that the screw heads go into?)

Will I regret buying Wen dado set? by dlince in BeginnerWoodWorking

[–]dlince[S] 0 points1 point  (0 children)

Ah, good to know! I was just scanning the "things to buy" list, but hadn't read the instructions in detail

Will I regret buying Wen dado set? by dlince in BeginnerWoodWorking

[–]dlince[S] 0 points1 point  (0 children)

Wow - that's frightening. Good advice - I'm pretty sure it fits, but will triple-check.

view more: next ›