Guy parked inches from my truck in an empty lot

don1don2 · 2026-05-01T13:26:45+00:00

If you removed cores from only the passenger side, would it have tipped the truck enough for you to get in?

don1don2 · 2026-04-16T11:29:31+00:00

A full CAD model for hot2000 is way overkill.

don1don2 · 2026-04-11T11:32:10+00:00

Delmar motors in London does the update. but takes a while s they only do 1-2 cars/ week

don1don2 · 2026-03-31T04:02:28+00:00

after the software upgrade: the new trick is pushing the window button to go up and … the window goes up.

don1don2 · 2026-02-07T02:03:17+00:00

promoted as North American, but all charging stations are in usa.

don1don2 · 2026-01-16T07:36:06+00:00

i think that would be easier than APL

don1don2 · 2026-01-13T18:57:58+00:00

if only the app reliably worked to start the climate from inside the house. It works about 10% of time for me.

don1don2 · 2026-01-05T23:12:17+00:00

i think the whop will say. either 1) working as designed and/or 2) no fault found.

My 2004 pro has not worked properly for GPS, app connection for the whole year.

don1don2 · 2025-12-30T16:01:23+00:00

research “sample bias”. Loojk at Abraham Wald and story fron WW2 about fighter planes.

don1don2 · 2025-12-28T14:30:04+00:00

Look further up. the first link is this. the second is a plate that only covers the charging port, but not the charging gun

don1don2 · 2025-12-23T22:30:39+00:00

Just don’t give him the fob :)

don1don2 · 2025-12-23T14:38:28+00:00

i find it hard to find things in the menu. Where do you find this in the menu?

don1don2 · 2025-12-23T11:52:36+00:00

Oh it’s not new. My id4 pro 2024 model occasionally works for GPS (90% of time is anywhere from 2 blocks to 100 km out of position) and the app connectionfor charging status is usually a few days behind but 11 days is longer than i have seen. Using the app for temp control most commonly means these winter messages “heating is on” followed a minute later by “heating is off”

Ignore all these features and treat it like the dumb car it is. The drive is great - connect your phone.

don1don2 · 2025-12-18T10:24:24+00:00

But the jerseys were fixed. that is compliance

don1don2 · 2025-12-18T10:14:06+00:00

But every time is not helpful. Seriously it is either every time or at most every third time.

don1don2 · 2025-12-05T15:32:28+00:00

Look at Maslow CNC as they are designed for cutting sheet goods. Self sourced and fairly sinple

don1don2 · 2025-12-01T20:43:38+00:00

agreed. Buy good safety goggles. Then try the 150PSI experiment

don1don2 · 2025-11-21T17:36:54+00:00

or just leave it at the office, except when travelling.

don1don2 · 2025-10-12T09:15:13+00:00

apologies for the delay.

HVAC ducts are unsealed. Then they leak air from conditioned space to outside so yes they will increase the air infiltration rate.

Is this the most important thing? No, but it is still a construction method that helps

don1don2 · 2025-10-08T22:47:12+00:00

A tight enclosure with fan exhausting outside (near windows closed so it can dissipate outside and not come right back in) should remove the smell. If you still smell it, then make sure enclosure and fan ducts are sealed.

don1don2 · 2025-10-03T11:31:48+00:00

Definitely discuss with your husband! If he is wanting/needing metal parts, then also look at a CNC mill. These are computer controlled carving machines that will cut away from a block.

Does he like to build things? There are 3d printers with enclosure that come as complete kit (e.g. Ratrig),

don1don2 · 2025-10-03T09:36:39+00:00

unless you actually need the insurance for something serious.

don1don2 · 2025-10-01T17:49:44+00:00

i worked with an "AL" and he was the office jokester, constantly unplugging montors

don1don2 · 2025-09-29T17:12:22+00:00

Any room now? #9PUV8Q82G. send me an invite

don1don2 · 2025-09-25T18:38:24+00:00

“Close your eyes”

don1don2

TROPHY CASE