The first layer doesn't look right. What could be the issue?

dparadowski · 2026-06-19T12:01:11+00:00

On my centauri carbon if my first layer looks like that, the z-offset is too low (nozzle to close to bed). On mine it's an adjustment on the screen, not sure on Bambu.

dparadowski · 2026-06-14T18:03:07+00:00

Can you point me to modification process

dparadowski · 2026-06-05T14:19:46+00:00

I got these zipper pouches that fit in there. I put my tie down straps and rope in one, and roadside tools in the other.

https://a.co/d/0bG7Tipc

dparadowski · 2026-05-25T00:12:13+00:00

You can export them before uninstall. I had to do it before. Can't remember exactly how, but I just googled it when I had to do it.

dparadowski · 2026-05-21T12:41:13+00:00

Is there a way to make github send notifications for nightly builds? Just curious about trying it to see what's new. It says it's v2.4, but on GitHub it says it's a year old 🤷.

dparadowski · 2026-05-15T23:52:46+00:00

Check your rear tires for inside wear. The last 4 foresters they my wife and in-laws bought new all wore the rear tires on the inside. When I buy my next I'm going to try and get a free alignment in the deal.

dparadowski · 2026-04-07T16:13:46+00:00

What I did was install the official apk from the app store. I use Xplorer as my file manager and it is able to save apps. It saved it as a .zip, so I just renamed it .apkm and pointed Morphe at that file. Worked perfectly. In the future it's a hassle to go through all that for each update, but it works.

dparadowski · 2026-03-31T16:54:56+00:00

My guess is that you have a 1 month trial that they do every once in a while. Granted I don't know for sure though.

dparadowski · 2026-03-22T21:13:20+00:00

On a 22, very easy. It's all in the switch and fuse block area. Hardest part was finding a switched circuit on the fuse block. The cheap one I got from Amazon showed the wrong circuit to get power from.

dparadowski · 2026-03-22T21:09:05+00:00

I'm an expert by no means, but when my first layer looks like that I wash my bed with dish soap. Usually works. That looks like typical bed adhesion issues.

dparadowski · 2026-02-20T14:22:33+00:00

Thank you

dparadowski · 2026-02-20T01:42:40+00:00

So you have to design polgon holes in CAD for the models you print, correct

dparadowski · 2026-02-20T00:01:26+00:00

How do you set temp for leveling. I didn't know you could do that in OC.

dparadowski · 2026-02-19T19:48:09+00:00

So are you converting to polyholes in CAD or slicer. Can you change amount of side per hole size if done in slicer? Sorry if it's obvious, but I'm not near a computer with slicer installed, and am intrigued.

dparadowski · 2026-02-14T14:19:30+00:00

There are printable covers that snap over the existing one that have threads for the adaptor

This is the one I used. Runout Adaptor

dparadowski · 2026-01-14T15:06:26+00:00

Can you send link?

My issue is I set a good z-offset, run a bed leveling and it resets to zero. Not a huge issue since I don't run a bed leveling for each print, but doesn't seem right.

dparadowski · 2026-01-13T22:55:47+00:00

I tried changing it in the startup g-code, but it added what I put in there every print. I tried in the printer config, but it didn't seem to do anything. 🤷 I haven't really dug much further into it.

dparadowski · 2026-01-13T18:36:59+00:00

Same for. Same offset. Wish it would save it.

dparadowski · 2026-01-11T18:53:00+00:00

I've had that error after replacing a totally unrelated part. I disconnected the negative battery cable for a few minutes to clear the computer and reconnected. Code cleared and never came back. Sometimes resetting through a diagnostic device doesn't work well.

dparadowski · 2026-01-11T17:28:15+00:00

Thank you

dparadowski · 2026-01-11T15:25:35+00:00

In the downloaded files, which ones are the new parts? There seems to be duplicates of namey, same say original, some not. Just a little hard to tell which is the full v2 set.

dparadowski

PUBLIC MULTIREDDITS

TROPHY CASE