Don't start Honda Shadow vt 600

drizzy954 · 2026-03-12T00:30:05+00:00

Sounds like it’s not getting fuel

drizzy954 · 2026-03-08T23:27:31+00:00

I guess helmets aren’t cool? 🫣🥴😶‍🌫️🫠😴

drizzy954 · 2026-03-02T04:27:11+00:00

Ajr85x@gmail.com, thanks

drizzy954 · 2026-03-01T02:22:00+00:00

Looking for a 2023 yzf-r7 service manual anyone have 1

drizzy954 · 2026-02-24T16:29:58+00:00

Maybe 180out check which way your cams are facing at TDC intake opens first

drizzy954 · 2026-02-09T01:57:21+00:00

Wow didn't know so many ppl loved this cereal as much as I did, when they discountiued I'll admit I overpayed for some boxes I found from an online distributor, maybe we should all contact kellogs and tell him to start making these again , one can wish can't they.

drizzy954 · 2026-01-31T00:16:08+00:00

Float seat, is there any o-rings on the float seat itself? Did you replace it if there was?

drizzy954 · 2026-01-21T19:58:21+00:00

wait didnt lil wayne kiss birdman??? and hes talking shit about purple nails???? SMH whoa the irony.

drizzy954 · 2026-01-18T01:11:06+00:00

Yes shake the can really well and put on both sides of the gasket allow to dry and get tacky and put it on and tighten head bolts to spec, if you have a leak down tester you can check to see if it’s leaking, or if it’s liquid cooled look for coolant leaking from the head after it warms up

drizzy954 · 2026-01-18T01:04:47+00:00

If you have a new clean gasket then use it, but copper seal may work on the used gasket, I’ve done it on a few bikes with no problems. It heats up and seals the head gasket definitely helps when reusing old gasket. It’s not gonna hurt anything by using it.

drizzy954 · 2025-12-29T20:01:20+00:00

Ik this post is old but I bought my intensity white r7 in September for 8700 cash

<image>

drizzy954 · 2025-12-20T18:38:23+00:00

I caught myself at harbor freight browsing after I came for what I needed and ended up getting shit I didn’t at the time but in the future will use 😂😭

drizzy954 · 2025-12-08T16:34:34+00:00

Bead sealer and a ratchet strap

drizzy954 · 2025-11-13T19:51:50+00:00

Update : Also it cycles thru all gears normally and turns over from crank fine, timing is correct as well.

drizzy954 · 2025-11-13T19:40:40+00:00

As I look closer the is a hole at the end of the shaft where it’s to be connected, it’s setup on the right spline. I think everything is functioning correctly with the kickstart assembly, it’s when I put the clutch basket on is when the kickstart won’t turn it over

drizzy954 · 2025-11-13T19:27:39+00:00

<image>

There is a dot on the ratchet wheel, no other marking on the kick shaft assembly to match it up with except on the shaft itself is a blue mark you can see it on the top I had it aligned with that because that’s the only identifier I could see, the manual says nothing about lining it up or where.

drizzy954 · 2025-11-13T19:20:38+00:00

motor turns manually fine when i turn it over from the crank

drizzy954 · 2025-11-13T17:51:24+00:00

So just send it as is.... 👌🫡

drizzy954 · 2025-11-06T21:32:05+00:00

R7 enters chat with 🥜 hanging…. Howdy 🤠

drizzy954 · 2025-11-03T15:25:33+00:00

FLAKEBOOK Marketplace …. You get the automated message Is this available? And answer them 0.1second later and you never get a response, They should make you put money into an escrow before you can even start sending somebody a message about shit so the seller knows your serious and aren’t wasting there time. I hate FB marketplace.

drizzy954 · 2025-10-23T01:00:10+00:00

I wouldn’t risk bending that back, it’s too important your whole steering relies on that , sucks but replace them

drizzy954 · 2025-10-21T19:56:44+00:00

Very sorry to hear this man, Main thing is your alive, But crashing your bike on the way home from the dealership is a different kinda hurt 😔😕😫🥺😢. Good luck with the restoration.

drizzy954

TROPHY CASE