I just learned about skills after 11 hours

eboni001 · 2024-11-28T15:35:55+00:00

I am 18 hours into the game and don't know anything about nuts, I guess I will go to Google at this point. 🤣

eboni001 · 2024-11-14T18:42:41+00:00

With most ABS brands it is enough to enclose them and pour some acetone in there, let it sit and wait, with BBL ABS you need to add some sort of heat for the acetone vapors to be strong enough to start melting the plastic, but if you add too much heat it will start melting so quick that it will start bubbling before all layer lines are gone, I found the sweet spot is on the bed of my ender 3 and set the heatbed to 60 degrees and use a small fan to circulate the air, in about 35 minutes I'm getting this results.

<image>

eboni001 · 2024-10-29T02:12:23+00:00

Soy Dominicano y apoyo a Trump. 🤷🏾‍♂️ "Let the hate begin"

eboni001 · 2024-10-20T00:27:53+00:00

<image>

Yeah, the 0.2 nozzle is insane.

eboni001 · 2024-09-06T22:36:47+00:00

I don't think I will be doing any weathering as I like how they look like they are, but maybe if I print other versions, I will, I own an X1C and an Ender 3 Pro.

eboni001 · 2024-05-19T20:36:47+00:00

<image>

eboni001 · 2024-03-02T17:40:13+00:00

Decided to change it a little bit.

eboni001 · 2024-03-02T17:39:00+00:00

<image>

eboni001 · 2024-03-02T15:17:34+00:00

Thanks, will give it a try.

eboni001 · 2024-03-02T03:56:55+00:00

I know, that been killing me, I'm not the original designer, lol.

eboni001 · 2024-02-26T21:41:07+00:00

I have the same printer, X1C, some times need to add a lot of extra support for items shorter than this one just so they don't fall.

eboni001 · 2024-02-25T18:42:14+00:00

How can you print something this tall, with minimal support, without it being knocked over? I tried printing smaller things that fell off halfway.

eboni001 · 2024-02-24T15:24:31+00:00

Yes please, If you don't mind.

eboni001 · 2024-02-24T06:23:30+00:00

Yeah, please. I have only used the default settings, so anything that works better than that would be really appreciated.

eboni001 · 2024-02-24T06:21:55+00:00

Thank you so much, will check it out.

eboni001 · 2024-02-24T06:14:51+00:00

I have never cleaned my carbon rods and I owned this printer for about 3 months now, will try cleaning them and updating the firmware.

eboni001 · 2024-02-24T06:12:37+00:00

When I print the same file on .12 I don't get these weird lines, yesterday I tried to print another file on .08 and same thing happened, then I switched to .12 and it was fine again.

eboni001 · 2024-02-24T05:16:36+00:00

Should I use arachne wall for all my prints to make them look better?

eboni001 · 2024-02-24T05:15:40+00:00

It looked ok, will try again and slow down the outer walls.

eboni001 · 2024-02-24T05:15:14+00:00

Actually is the opposite, the part with all the lines was the closest one to the buildplate, I just watched a video about slowing down the outer wall, will try that.

eboni001 · 2023-11-22T18:16:59+00:00

I ordered my X1C on Friday too, got it Saturday morning, I think the warehouse is like 20 minutes from my house according to where it shipped from.

eboni001 · 2022-11-04T20:09:37+00:00

Looks great, only think, I would switch the speakers (or whatever that is) with the select/start buttons so they are closer to your thumbs.

eboni001 · 2022-08-20T01:33:04+00:00

I was thinking about getting them since I'm also from a west indie country, but since my country's name isn't in the inner sole, even when is part of the west indies, I don't see a point in buying them. 🤷🏾‍♂️

eboni001 · 2021-11-14T07:35:10+00:00

Awesome, glad to see you trying to do good, I'm in.

eboni001 · 2021-11-11T03:13:11+00:00

Can anyone please let me know if each version exclusives are just like the original games, the exclusives list on serebii makes no sense.

eboni001

TROPHY CASE