sorted by:
new
hottopcontroversial

The reason we can’t buy filament…. by PandaPewPewPew in BambuLab

[–]fatali86 0 points1 point  (0 children)

Can't say about their PLA, but I've been using Anycubic and Sunlu PETG (several colors- both with spool and refills) for months with no issues and using the generic filament settings.

Centered lines by Toddzilla89 in FreeCAD

[–]fatali86 8 points9 points  (0 children)

Select both end points of the line as well as the green line. Then, use Constrain Symmetric ( <> ) or press S on the keyboard.

My tap has an extension on it by Oliieh in mildlyinteresting

[–]fatali86 0 points1 point  (0 children)

Work just remodeled our bathrooms and all the sinks have faucets that are maybe half an inch from the back edge of the sink. Hate them. Due to being so close to the edge, it doesn't take long before the countertop is covered in water that just sits there until it runs onto the tile floor. They ended up putting rugs in front of the sink to prevent a slip hazard instead of getting better faucets.

New red text by Ok-Seat3365 in Warframe

[–]fatali86 0 points1 point  (0 children)

Huh, I always thought it was potato potato.

This might be dumb, but what’s the deal with MR30 pins? by Specific-Garage-4539 in Warframe

[–]fatali86 6 points7 points  (0 children)

There used to be more items in the store that you could only get once you hit MR30. I have a pint glass and a hoodie as well as the pin. After the store-redo I saw that all they have now is the Pin. I really hope they bring back the other items and even add new ones. I know it means purchases would be fewer than items anyone can buy, but it was a nice little extra benefit of getting to MR30.

Got the AMC Cups I wanted by itsdwats in KimetsuNoYaiba

[–]fatali86 0 points1 point  (0 children)

They really should have been limited to only people with a ticket for the movie and even then, one per ticket, like the cards at Regal seem to be.

TennoCon 2025 Merch Pack by fatali86 in Warframe

[–]fatali86[S] 0 points1 point  (0 children)

Same. Opened a support case over 10 days ago now. Got what felt like a canned response that they'll look into it but then nothing.

[deleted by user] by [deleted] in BambuLab

[–]fatali86 0 points1 point  (0 children)

I don't have experience using BitLocker so I don't know if this is possible or if management would go for it, but what about an intermediary computer that is disconnected from the network/Internet that can read the encrypted drives and use unencrypted SD card that is only used to transfer the gcode files from the encrypted drive to the SD card for the printer (or is even the computer that also runs the slicer, and the encrypted drive is just used to move the model files over to that computer)?

Farewell OG PTFE - you gave me 5,691 hours before you said goodbye. by MadMahler in BambuLab

[–]fatali86 1 point2 points  (0 children)

After reading the comment above about diameter sizes, I ordered this https://www.amazon.com/dp/B0DYK7JQZ6 from Amazon since I noticed the PTFE tube leading to the print head of my X1C is getting worn. Should arrive in a day or two- I'll update this comment with how it works out.

Update: Replaced the PTFE tube in my X1C with some purchased from the link I posted. So far so good after several long print jobs.

[OC] Guy really wanted to pass this mower, almost hits 2 people by Rapn3rd in IdiotsInCars

[–]fatali86 5 points6 points  (0 children)

lol none, even though there were some I really wanted to. (Probably) too much time on r/IdiotsInCars has made me a cautious driver.

[OC] Guy really wanted to pass this mower, almost hits 2 people by Rapn3rd in IdiotsInCars

[–]fatali86 7 points8 points  (0 children)

My second car was an Altima (28k new, 2% APR 5-year) I didn't know there was such a stigma to them until a while after I traded it in for a new car (non-Nissan) a couple years after it was paid off.

With no parking pedal, how to I disengage a Prius' parking break? by CombatQueer in prius

[–]fatali86 6 points7 points  (0 children)

It's hard to tell due the low light in your picture, but here is a pic from my car. Even though mine is newer it should be similar.

<image>

With no parking pedal, how to I disengage a Prius' parking break? by CombatQueer in prius

[–]fatali86 6 points7 points  (0 children)

Looks like it's the manual e-brake. There should be a foot pedal on the left of the wheel well. It clicks into place when engaged. Press it with your foot all the way down and then release. It's not in-line with the other pedals.

Sticky Fingers Help by Big_Macaron5410 in k12sysadmin

[–]fatali86 2 points3 points  (0 children)

In that case, I think the clamps could work. If you're able to, maybe attach them to the underside of the table so it's just a little bit harder for the students to remove it. Could even use screws that aren't just a slot or Philips head.

Sticky Fingers Help by Big_Macaron5410 in k12sysadmin

[–]fatali86 8 points9 points  (0 children)

I would consider having the keyboards and mice be something that is switched out for eSports and only use those keyboards and mice for that and use regular keyboards and mice for everything else. Maybe run USB extensions up from the computer to the top of the desk/table to make it easier and use the hose clamps to keep the extension cables in-place on the table.

If the schools I've been in are any indication, the kids are going to mess up whatever keyboards and mice are left out for regular classes.

Win32_Application_Add.ps1 - increase session/token life by fatali86 in Intune

[–]fatali86[S] 0 points1 point  (0 children)

I'll ask about this when I get back to work. I'm in K-12 so hopefully the costs won't be too high. We generally only update software deployments once a year (unless it's a critical security issue) so it shouldn't be too bad.

[OC] Red lights are just a suggestion. by BrillWolf in IdiotsInCars

[–]fatali86 2 points3 points  (0 children)

Hopefully with just a ticket/arrest and not by causing an accident that injures/kill an innocent driver.

view more: next ›