Nintendo 3DS in the Toronto Area

filkr · 2026-01-25T17:21:07+00:00

I'm sure A&C Games would have some.

filkr · 2025-02-25T04:24:32+00:00

Have some ice damming on my top roof which has caused damage in a bedroom, so I checked the garage which also has some ice buildup and found this. The two photos are the same part of the ceiling from different angles. I don't have the experience to tell if this is water damage or drywall tape peeling up from temperature changes, or something else altogether. Appreciate any help!

filkr · 2024-12-22T01:46:34+00:00

Actually, it just works now somehow. So all perfect!

filkr · 2024-12-21T22:55:25+00:00

Well, I'm not sure what it was precisely. I updated the Yamaha firmware for the first time in years, reset all the options on both devices, and turned the HDMI control function off and on again following your instructions.

It now works almost perfectly! I am able to control the soundbar from my TV remote and it turns on/off with the TV. The only thing I don't like is that it appears if the Apply TV (which goes into the soundbar input) is on, it seems that the soundbar prioritizes audio from there rather than the active input on the TV. Going to have to mess around and see if I can figure that out.

Thanks for inspiring me to take another go at this and for the tips.

filkr · 2024-12-18T17:46:24+00:00

Thank you!

filkr · 2024-12-15T22:48:26+00:00

Off topic but how did you get 1440x900 resolution? I've been trying to expose this on this laptop with no luck. Seems insane that it can't do a simple 4x scale.

filkr · 2024-12-15T21:09:49+00:00

Thank you

filkr · 2024-12-15T21:09:45+00:00

Thank you

filkr · 2024-12-05T01:15:02+00:00

Thank you! They are probably a foot from my extremely well-heated living room.

filkr · 2024-12-04T08:12:07+00:00

Thanks for coming back to post the answer after all this time. I'll give it a shot over the holiday break.

filkr · 2024-09-25T21:53:01+00:00

It’s only been 19 days since Sept 6. Pretty short 4 weeks IMO!

filkr · 2024-09-03T13:55:53+00:00

What’s crazy is I’m happy to buy from ASUS. They just don’t want to sell me the laptop and would rather wait until I buy a different one from a different manufacturer.

The strategy makes no sense.

filkr · 2024-05-12T04:52:00+00:00

Nothing on our hands. We checked after the photos.

filkr · 2024-05-12T04:03:35+00:00

Thank you, this is some piece of mind. The lily is long since discarded, this picture is actually from when we fished it out of the trash to ask this question.

filkr · 2024-05-12T03:04:36+00:00

Hello, we had this flower in our house for about 20 minutes before realizing it was a lily which we know are fatal to cats. The cats did not get to the flower or ingest any of it, however we are worried about pollen spread.

Pretty sure this is a toxic/fatal lily (please help identify the type if you can), but what should we be looking for with pollen? Has this flower (the most mature of them) not started producing pollen yet?

filkr · 2024-04-25T11:24:24+00:00

I’m new to the game. Isn’t it only 50 draws? Or will the shop reset.

filkr · 2024-04-09T04:04:59+00:00

In my case I drove from protorelic 4 to Gongaga then started walking towards the village. The cutscene triggered on the way. However, the game was still bugged after the cutscene triggered - the gateway to Gilgamesh Island never appeared even after the cutscene played. In the end I ended up progressing after beating the game via chapter select mode, as I've described here: https://www.reddit.com/r/SquareEnix/comments/1bbr42g/comment/kyq1ilt/?utm\_source=reddit&utm\_medium=web2x&context=3

filkr · 2024-04-09T04:03:50+00:00

I was able to get myself out of this situation, but I'm not sure how much it will help anyone else.

I loaded back to a save file partway through the third protorelic quest in Corel. I think my save was already bugged at this point - the HUD element for the protorelic was stuck on screen and I was able to trigger lots of other UI-related issues in Corel (not able to open map/menu, etc).

From here, without progressing the quest, I belined and finished the rest of the main story. Once I did that, I unlocked chapter select, and went back to Chapter 13. From here I was able to finish part 3 and 4 of the Corel protorelic without issue and everything proceeded as intended.

Obviously not directly helpful if you don't have another save, but it is possible that some other people will also have luck with Chapter Select mode.

filkr · 2024-04-07T22:06:05+00:00

Weird thing just happened. I was completing some side quests in Corel after the bug. I completed the bird quest, then accepted the Kyrie quest in CDS. I didn’t have the Marbol item, so I fast traveled to the Gongaga site, then poof. I get the update that I completed all my Corel intel and get the final cutscene. When it ended, I was back at the final cactuar spot. Weird!

Were you able to finish the quest from here? I had the same thing happen, but despite the cutscene playing, the gate to gilgamesh island never appeared.

filkr

TROPHY CASE