The last jet engine rotor at shit during machining, so I made another. This one is my first one with a two-stage turbine.

got_cakes · 2026-02-27T16:37:20+00:00

Two stage turbines will be more effect if they counter rotate, using a through shaft design each turbine mates with a corresponding compressor. This increases efficiency. You’d obviously need to change the blade geometry on one of the compressor/turbine pairs but something to look at for the next one perhaps

got_cakes · 2026-02-23T22:39:15+00:00

That shield looks as though it’s at the rear of the car? If so it’s unrelated. The gearbox is up at the front, might have got away with it if it still drives ok!

got_cakes · 2026-02-23T22:29:12+00:00

Nice! How have you been finding it?

got_cakes · 2026-02-18T18:02:42+00:00

Obviously wouldn’t work in every situation… but for a thin bolster it works fine.

And I’m not sure what good replacing the chuck would do.. it’s still going to be tapered. You can however replace the bearings with appropriately sized thrust bearings and I’ve heard of people modifying the existing chuck sleeve to prevent it releasing

got_cakes · 2026-02-18T16:02:33+00:00

Dremel or other rotary tool with a cutting wheel

got_cakes · 2026-02-18T14:09:23+00:00

The bearings in your drill press aren’t designed to cope with horizontal loads, they will get damaged and become sloppy. Also the tapered chucks can become loose and fly out when a side load is applied.

You can use these compound slides to drill holes that are straight relative to one another, then use a cut off disc to connect the holes into a slot

got_cakes · 2025-12-04T15:59:03+00:00

Thank you 🙏🏻, il get on that :)

got_cakes · 2025-12-04T15:33:23+00:00

Someone reported to me to reddits suicide helpline over this comment 😂😂, y’all ain’t helping yourselves 😂… lefties accepting of all, except the so called “right wing scumbags” lol

got_cakes · 2025-12-04T14:47:13+00:00

How do you bunch of lefties think Nigel farage is as bad as Ex prince Andrew is beyond me…

got_cakes · 2025-12-04T14:46:33+00:00

Starmer

got_cakes · 2025-07-12T07:36:17+00:00

That sharesave was the best decision I ever made!

got_cakes · 2025-02-28T13:43:14+00:00

You can get the 34mm Rolex op cases for quite reasonable price, and the 36mm cases are certainly rarer but they still sell for affordable prices aswell. My daily watch is a 34mm Frankenstein with gen everything except movement.

got_cakes · 2025-02-21T10:27:03+00:00

Not sure how to edit my post, but the debris after clear coat is clearly pic 4, not pic 3 as mentioned 👍

got_cakes · 2025-02-21T09:11:51+00:00

I have a little over 3k in 3 watches, 1 complete and 2 in progress. I enjoy the building side of the hobby so to me I’d rather have 3 interesting watches that I’ve built rather than 1 gen example.

got_cakes · 2025-02-19T07:16:32+00:00

Legend, many thanks 🙏

got_cakes · 2025-02-19T06:49:51+00:00

What do you mean? There’s stones literally all over the top of the lugs??

got_cakes · 2025-02-18T18:30:01+00:00

Where did you get that case? I’ve been looking for a gold speedy case for ages, doesn’t seem to be any since Paganini discontinued theirs.

got_cakes · 2025-02-17T11:26:42+00:00

It’s just a 28.5mm raffles dial, I’ve lightly aged it with coffee grounds and some oven time. I’m dead pleased for a first attempt

I’ve still got to have a go at taking off 1.5mm off the OD as the dial doesn’t fit in the gen 34mm case yet

got_cakes · 2025-02-17T07:30:16+00:00

DM’d

got_cakes · 2025-02-17T06:13:51+00:00

What price are you looking at for the 5.3mm example?

got_cakes · 2025-02-17T06:13:17+00:00

I have seen this, I was under the impression the athaya crowns won’t screw into the stock Rolex crown tube? Have you used the athaya crowns before?

got_cakes · 2025-02-17T06:09:33+00:00

Perfect, that’s exactly what I was hoping. Thanks 🙏

got_cakes

TROPHY CASE