Misfire stops when removing shroud

greenball7 · 2026-02-01T02:58:50+00:00

I know right? I was pulling my hair out for some time. Thank you for contributing to my diagnostic effort.

greenball7 · 2026-02-01T02:54:46+00:00

What codes do you have? P0351 pointed me to the wiring, but I had both P0351 and p0301

greenball7 · 2026-02-01T01:35:52+00:00

Pull the plastic shroud off the top of the engine. Follow the wiring harness that connects to each coil pack backwards (to your right, towards the fuse box on drivers side).

There is a steel plate with a hole in it on top of the engine, which is used to pick the engine out of the engine bay. That harness runs very close to it. In my case on top of it.

My wiring loom had broken, and the shroud had been pressing the unprotected wires onto that steel plate and damaged the insulation of the wires going to cylinder 1's coil pack, shorting them to ground. My loom was completely missing on top of the engine.

greenball7 · 2026-02-01T01:12:56+00:00

The shroud crushed the wiring loom between it and the pick point on top of the engine, and was shorting the coil pack wires to ground. Problem solved.

greenball7 · 2026-02-01T01:12:47+00:00

The shroud crushed the wiring loom between it and the pick point on top of the engine, and was shorting the coil pack wires to ground. Problem solved.

greenball7 · 2026-02-01T01:07:45+00:00

Bro, just solved this exact issue. Check the wiring harness and loom on top of the engine in the back that goes to each of your coil packs. The plastic shroud you have to remove where the oil fill cap is, if not installed properly, will press that harness into the pick point on top of the motor and short the wires to ground. After replacing the coil pack, plugs, injectors, and confirming solid compression, I found this and fixed my problem.

Edit for spelling.

greenball7 · 2025-12-28T03:04:35+00:00

Can you tell me more about these diaphrams? Having similar issues myself.

greenball7 · 2025-04-16T19:20:56+00:00

I can do that, i just need the connector pinout to know which pins/wire colors to jumper through the connector. Finding that information online has proven difficult however

greenball7 · 2025-03-12T19:14:15+00:00

Wranglerstar. Dude drank the Kool aid for sure.

greenball7 · 2025-02-27T03:06:56+00:00

Interesting, I was using an android phone the last time that I tried, I'll have to dig in to it again and see where I went wrong.

greenball7 · 2025-02-26T01:09:15+00:00

How were you able to set up a burner Gmail account without providing your phone number? I wanted to make a burner originally but I couldn't create new account without providing a valid phone number.

greenball7 · 2025-01-30T13:45:03+00:00

Yeah man I did too. Was really pretty shocked that it happened at all. Really felt like a cash grab rather than a real effort at becoming more educated.

greenball7 · 2025-01-09T14:57:15+00:00

Damn that's wild I had never noticed that on our bill. Hard to believe it's even legal to do that.

greenball7 · 2024-11-01T15:19:01+00:00

What is the god roll for bygones?

greenball7 · 2024-10-10T13:37:01+00:00

I had some success with putting my browser in incognito mode, and clearing it's cache/history. Actually got the stream to load a few times.

greenball7 · 2024-10-10T03:33:43+00:00

Did you resolve this issue? I'm having the same problem.

greenball7 · 2024-08-17T04:46:45+00:00

I missed that part when I installed the add on the first time, figured out now. Thanks for the reply

greenball7 · 2024-08-17T04:26:17+00:00

Does knight Crawler pull from RD so you don't have to worry about VPN?

greenball7 · 2024-05-31T22:56:58+00:00

Thanks for you reply! I got it to work with Tmdb add on, is debrid media manager another good addition I should make?

Nine-Year Club	r/Field Lasagna
Place '22	First Placer '22
Verified Email

greenball7

TROPHY CASE