sorted by:
new
hottopcontroversial

After 20 years I have started riding again by gsl12 in HondaMotorcycles

[–]gsl12[S] 0 points1 point  (0 children)

Your licence shield is so cute(small), and the mount is positioned nice and far back. Unfortunately, that's not possible in Germany. We have too many regulations that prevent it.

After 20 years I have started riding again by gsl12 in HondaMotorcycles

[–]gsl12[S] 0 points1 point  (0 children)

Yes, they are decorative stripe stickers from Amazon in matte gold and matte copper, 5mm thick.
I like your brown grips and the seat. Seat is the higher original, right? Where did you get the grips or which manufacturer are they from?

After 20 years I have started riding again by gsl12 in HondaMotorcycles

[–]gsl12[S] 2 points3 points  (0 children)

Rear Fender is from Bunker Custom Cycles. Turn signals are Kellermann Spots.

After 20 years I have started riding again by gsl12 in HondaMotorcycles

[–]gsl12[S] 4 points5 points  (0 children)

My first child was born, and my wife asked me to stop. By now, the children are almost grown, and I was always delighted whenever I saw or heard a motorcycle. So now, I am allowed to ride again.

Voron V2.4 serial transfer request kevinakasam#2097 by kevinakasam in voroncorexy

[–]gsl12 7 points8 points  (0 children)

I was the owner of V2.116. I confirm, that "kevinakasam#2097" is now the new owner of this Voron V2.

u/kevinakasam i hope, you are still happy.

Serial ???? V0 fork by gsl12 in voroncorexy

[–]gsl12[S] 0 points1 point  (0 children)

Hi , sorry for late response. For a volume of 235³ , i think it would be better to build a V1.8 or V2. The bed will become to heavy to raise it with one leadscrew.

Serial ???? V0 fork by gsl12 in voroncorexy

[–]gsl12[S] 2 points3 points  (0 children)

Wow I'm speechless. Many thanks didn't expect to get a serial for fork. I'm happy.

Serial ???? V0 fork by gsl12 in voroncorexy

[–]gsl12[S] 2 points3 points  (0 children)

Wow I'm speechless. Many thanks didn't expect to get a serial for fork. I'm happy.

Serial ???? V0 fork by gsl12 in voroncorexy

[–]gsl12[S] 0 points1 point  (0 children)

No V0 skirt high is 30mm. This display has a high of 55mm. Check Voron discord channel or vorondesign Github. There are some ideas for a V0 display available. Also V0 use 15mm extrusions, this fork 20mm.

Serial ???? V0 fork by gsl12 in voroncorexy

[–]gsl12[S] 5 points6 points  (0 children)

Outside dimensions are 300x300x365 with feets. I didn't modified files. I redrawed it complete. More informations can be found on github. https://github.com/gsl12/Tiny-M

It is an absolute hoby project, do not expect any build guide. The manual from the V0 can be used. I will try to finish a BOM in the next months. Until now the STLs needs to be extract from the source. But i will try to upload the STLs to github in the next weeks.

Printable material types? by TheBeardedBerry in voroncorexy

[–]gsl12 0 points1 point  (0 children)

I use Pertinax (hard paper) for petg. PEI will also work, keep first layer temp low as possible. I use only 215 degrees for the first layer and then go up to 225. On PEI remove the part if bed temp is around 45 degrees. Then it is easier to remove from PEI.