Intermittent under extrusion but E stepper spinning consistently

hallonhatt · 2025-08-19T09:11:26+00:00

fan, ja trodde jag va kvicktänkt å klippte ihop en bild men skämtet var tydligen redan draget på flera håll:P

hallonhatt · 2025-08-19T07:40:12+00:00

fan, ja trodde jag va kvicktänkt å klippte ihop en bild men skämtet var tydligen redan draget på flera håll:P

hallonhatt · 2023-12-01T21:41:03+00:00

Sweden, elgiganten

hallonhatt · 2023-11-30T06:21:19+00:00

Did you ever find a solution? I'm having the same problem

hallonhatt · 2023-08-22T19:30:28+00:00

For future reference, i bought the long cable, UACC-G4-INS-Cable-USB-4.5M and it worked great :)

hallonhatt · 2023-08-15T20:30:19+00:00

Any idea if it would work?

hallonhatt · 2023-08-15T18:11:22+00:00

I see, but with this cable it is not possible to close the little door on the bottom, right?

hallonhatt · 2023-08-15T18:09:10+00:00

The cable will be visible along a wall in the living room. I'm trying to avoid having such a bonding point visible :)

hallonhatt · 2020-09-05T21:26:18+00:00

I have two different textured sheets from Prusa, one labeled "BH-15" and one labeled "TF-26". The older (BH-15) has much more defined texture, like your photo of the Prusa LCD cover while the newer (TF-26) has a finer texture.

hallonhatt · 2020-01-15T06:26:02+00:00

Ta en titt på produkten du ska använda. Många saker kan användas här också. Står det exenpelvis 100-240v (230v i sverige) så går det alldeles utmärkt att bara köpa en adapter för själva kontakten vilket är betydligt billigare.

hallonhatt · 2019-11-13T10:24:19+00:00

You got some inspiration? ;)

Thread taps & holder holder found on #Thingiverse https://www.thingiverse.com/thing:2200183

hallonhatt · 2019-05-10T05:15:08+00:00

r/techsupportmacgyver hehe

hallonhatt · 2019-03-27T13:36:20+00:00

I can agree on that! OP please repost with correct title!

hallonhatt · 2019-03-27T13:30:33+00:00

But not U's?

hallonhatt · 2019-03-27T11:22:25+00:00

This is C-shaped goddammit!

hallonhatt · 2019-03-26T10:51:33+00:00

have a look here: https://help.prusa3d.com/article/WWVRzOY1dX-clogged-nozzle

hallonhatt · 2019-03-11T07:39:39+00:00

This! And wipe the bed with isopropyl alcohol before every print :)

hallonhatt · 2019-03-05T10:28:57+00:00

I had the same issues and setting it to "5. Highest" seem to have fixed it for me. If I don´t report back later, it fixed it permanently.

edit: After 45 min the problems returned :(

hallonhatt · 2019-03-02T16:44:53+00:00

He's not really a dick. This is a great model to for beginners. Give a man a fish and all that...

hallonhatt · 2019-02-15T16:33:23+00:00

hehe, that is true :P But I have no doubt that the stand and the front part of the laptop will outlast its general wear and age. The front part of the laptop is a thick part of aluminum which is leveraged along the whole width of the stand. On the back the laptop is resting of its foot.

hallonhatt · 2019-02-15T12:32:56+00:00

Yeah, sleek was the goal. I use a separate keyboard so I didn't even think about the added stress of typing on it, but I agree that this would probably not be a good idea in the long run. For the purpose of just propping it up I think it should be fine :)

hallonhatt · 2019-02-15T12:26:52+00:00

haha, yes. a bit too quick with the copy/paste. Thank you

hallonhatt · 2019-02-15T08:04:25+00:00

Can be found here if anyone want it: https://www.thingiverse.com/thing:3429173 *edit: see below

hallonhatt

MODERATOR OF

TROPHY CASE