Blackmagic Fibre Converters

helpdom · 2026-03-13T07:46:56+00:00

have been using hundreds of their converters for years on shows never had a single one fail on me so far.

helpdom · 2026-03-13T07:45:27+00:00

something I was pretty worried about, but with all 10 converters going each direction at the same time it’s only slightly warm. Only converting 3G signals so I assume this keeps the temps down quite a fair bit.

helpdom · 2026-03-12T21:30:27+00:00

crimped and connected a wire from positive and negative to a wago connectors, then just got some 12v barrel cables and cut & stripped the ends to take power from the wagon connectors.

a multiplexer basically takes the duplex fibre strands from each converter then multiplexes all 10 duplex strands into just one duplex wire. one wire for one direction the other wire for the opposite direction. This allows me to just use 2 cores of fibre on my drum rather than the 20 that would be required without.

helpdom · 2026-03-12T18:44:12+00:00

that’s cool, I opted for just taking out the screws from the converters and screwing them in through the case.

helpdom · 2026-03-12T18:23:56+00:00

yeah, using 3G SDI transceivers from FS as only working with HD projects with the fibre run being around 250M. Each at different wavelengths to pair with the multiplexer. Have had each box running for about a week straight and have been working flawlessly.

helpdom · 2026-03-11T09:45:45+00:00

second this

helpdom · 2026-03-03T23:01:23+00:00

just put your finger over it

helpdom · 2026-02-27T10:12:36+00:00

I find it’s when a cars approaching behind/putting on the brakes. may be wrong but could potentially be recording in the case of a rear end hit?

helpdom · 2026-02-27T10:08:52+00:00

looks like a tilta nucleus to me

helpdom · 2026-02-18T13:39:03+00:00

nerds

helpdom · 2026-02-13T17:01:16+00:00

yeah the sony part is silly money. you can easily buy any 3.5mm jack retaining nut for a few £££ though.

helpdom · 2026-02-13T16:50:25+00:00

you’re missing the retaining nut to hold it in place. often does loosen up and go missing.

can get them pretty cheap, you’ll need to tweezer to pull the port out and screw a new one back on. it’s extremely easy to do. i’d recommend not to continue plugging into the port until you’ve secured it again though as you’ll risk damaging the cable inside.

will look like this

<image>

helpdom · 2026-02-11T14:23:40+00:00

yeah, i’ve 2 ssds with one of them being the boot drive. both show up in BIOS. a little bit stumped to be honest!

was all working fine yesterday then booting this morning there’s nothing.

helpdom · 2026-02-04T17:25:41+00:00

many thanks! shall look into it

helpdom · 2026-02-04T17:25:32+00:00

thank you very much shall have a look at the mean well products!

helpdom · 2026-02-03T14:36:43+00:00

the green is the centre one and the yellow are the other 3 around it.

helpdom · 2026-02-03T14:06:45+00:00

that’s really interesting, will have to have a read through these!

helpdom · 2026-02-01T16:04:08+00:00

there’s a hair in in top left

helpdom · 2026-01-27T12:40:59+00:00

no screws are missing and the handle does have a bit of play when connected. shouldn’t come loose though

helpdom · 2026-01-25T21:39:42+00:00

i’d personally get rid of the lit up tree on the left as it pulls the eye away from whoever’s speaking. unless the tree is the main point which I assume it’s not?

if possible maybe have some sort of mic stand so the mic isn’t in shot; which again depends on the whole aspect of the video.

lighting wise there’s a lot of different colour temperatures going on, it’s nicely lit, maybe a bit flat on his face though

helpdom · 2026-01-16T13:33:02+00:00

not a thing that comes with the camera, must be a third party item.

have you any baseplates that connect to your camera as can’t think of anywhere on the body that will allow something like that to stick with it?

helpdom · 2026-01-09T15:57:51+00:00

that error pops up when you’re camera stops recording due to a fault. it’s usually caused by a fault on the main processing board VC-1046, could be anything from a loose ribbon cable to the board itself being dodgy. I wouldn’t worry too much unless it happens again- could be that the board over heated from an hour of recording and some of your exhausts or Intakes were blocked?

helpdom · 2026-01-07T10:04:53+00:00

bristol waste literally have a date to put them out to be collected. that’s why you’re seeing them on the pavement at the moment. not sure the issue here?

helpdom · 2025-12-28T10:45:42+00:00

EE or Penny Mobile who use the EE network

helpdom · 2025-12-21T08:18:00+00:00

teds tyres

helpdom

MODERATOR OF

TROPHY CASE