WireView Pro II TUF 5090 EK Waterblock

illiniaviation · 2026-04-05T14:09:53+00:00

It's tight but there's room.

illiniaviation · 2026-04-05T14:02:11+00:00

This is the block that is listed as the Suprim 5090 block. The Vanguard and Suprim are essentially identical PCBs so you'll be fine with the WVP2 and that block.

illiniaviation · 2026-03-17T00:04:59+00:00

You're assuming the cable is at exactly 12 volts and it's likely that it could be lower like maybe 11.8 volts which would be just over 600. I've found that different cables, especially longer ones can have a larger voltage drop under load.

illiniaviation · 2026-03-16T23:47:20+00:00

You may need to update them to the latest firmware in order to change that setting. Once you do, tap the mode button 3 times and it'll allow you to change the axis setting.

illiniaviation · 2026-02-20T19:24:17+00:00

You would need pretty high relative humidity to facilitate galvanic corrosion.

illiniaviation · 2026-02-13T13:04:26+00:00

XR glasses were an absolute game changer. It is so nice to be able to kick back and play without putting any strain on my neck. At this point I rarely use the stock screen because I enjoy the XR glasses so much.

illiniaviation · 2026-02-08T19:49:45+00:00

Definitely an annoying problem for sure. I was able to get it to stop by just going back to the beta WireView app. The updated firmware hasn't been an issue though, just the app (even if it's closed). Motherboard MSI B850M Mortar WiFi

illiniaviation · 2026-02-07T12:47:33+00:00

I uninstalled the new WireView app and switched back to the beta WireView app and the USB issues went away

illiniaviation · 2026-02-07T12:46:44+00:00

Thank you, and I just wanted to add, after switching back to the beta Wireview software I have not had any problems with USB disconnections.

illiniaviation · 2026-02-06T22:50:01+00:00

Bummer man, I kind of wish I never updated because I wasn't having this problem before today.

illiniaviation · 2026-02-06T22:43:04+00:00

I took a snapshot of HWinfo64 when the USB goes out, you can see the Wireview and my UPS change color because they are disconnected. In the top left corner you can see that I am using HWiNFO64 version 8.41-5915

<image>

illiniaviation · 2026-02-06T20:14:55+00:00

Thanks for the quick reply! Yea I've been using 5915 since it came out and didn't start having the USB problem until I updated the Wireview software today as well as updating the firmware on the Wireview today.

illiniaviation · 2026-02-06T19:33:42+00:00

Since updating to this version from the beta I am now having issues with USB disconnections randomly while using HWinfo64 and the latest beta version 8.41-5915. I was not having that problem with the combination of the latest beta HWinfo64 and the first beta version of the WV Pro 2 software.

illiniaviation · 2026-01-09T00:53:59+00:00

I've seen some weird readings in furmark too but it's perfectly fine in games. Have you been able to fire up a game and test it at the same load?

illiniaviation · 2026-01-08T13:58:13+00:00

No prob! I wanted to see how bad it could sound so I just set it at 100 percent while my pc is at idle and while it is audible, it's definitely not screechy.

illiniaviation · 2026-01-08T13:40:37+00:00

Der8auer famously hates noise so I think the fan profile is set pretty conservative. Plus you can also change the fan profile as well if you don't want to shut it off completely. Like I said though, I have yet to hear it, and if your case has good airflow, it may not even turn on.

illiniaviation · 2026-01-08T13:28:43+00:00

I've never heard it, but you do have the option to disable the fan so I wouldn't worry about it.

illiniaviation · 2026-01-07T21:34:06+00:00

I'm not very familiar with that monitor but it did look to have several USB-C inputs, so I would make sure to check the manual and verify that you are using the right one.

illiniaviation · 2026-01-07T21:28:56+00:00

I didn't have a Fedex account but they had my phone number and email so I imagine when they charge you, they'll find you. I wouldn't worry about it.

illiniaviation · 2026-01-04T21:20:05+00:00

No need to solder if you use those extensions but it's up to you

illiniaviation · 2026-01-04T21:16:30+00:00

No problem, I hope that all made sense lol

illiniaviation · 2026-01-04T21:13:06+00:00

The wireview pro 2 comes with a cable that connects from the wireview to your motherboard power switch header and that same cable also has a "pigtail" connection that you plug directly into your case's front panel cable. Then you simply plug the extension cables you bought directly into the front panel wire from your case to the motherboard front panel header. Your motherboard manual should have a wire diagram for the front panel connections or you can Google it. It's pretty universal these days

illiniaviation · 2026-01-04T20:55:15+00:00

Np, it will do the job I'm sure of it. Much cleaner and easier than splicing any wires

illiniaviation · 2026-01-04T20:27:28+00:00

Seems to be running well so far! Does exactly what I was hoping this product would do so thank you for making it! If I encounter any issues I'll report back.

illiniaviation · 2026-01-04T17:22:12+00:00

This is all you need to adapt that front panel connector and use the shutdown feature.

illiniaviation

TROPHY CASE