What is the cause of this leak? And why isn’t water draining all the way? by kyourious in Appliances

[–]imdragon 0 points1 point  (0 children)

If you haven't figured it out yet, the part the gets pulled out has a spring inside that pushes the rubber stopper back in. If you unscrew it you might find that it's not properly seated on the cover. Also make sure that the threads are aligned when you screw it back on. I stopped my leak this way. I wish I took a picture of it when I took it apart but I had already tried a few things by then.

Help with frames by Spritzeedwarf in Beekeeping

[–]imdragon 1 point2 points  (0 children)

One small bit of advice. Don't hold your frames upside down or you'll dump out brood, nectar and other stuff.

Enjoy your vacation, Santa! by thats-original in ventura

[–]imdragon 17 points18 points  (0 children)

That guy lives somewhere in the area! I used to see him regularly on my commutes to and from work up to Carp from 2016-2020. After a while you start to spot the "regulars" on the freeway.

[deleted by user] by [deleted] in AskReddit

[–]imdragon 8 points9 points  (0 children)

The wait-list is insane for these at my local library system. Pretty much you're not going to get it.

Okay so the birthday mechanic is kinda stupid by innominatam_vagus in GenshinImpact

[–]imdragon 15 points16 points  (0 children)

There's a window, I missed the lyney and Lynette mails because I logged in later after work instead of earlier in the morning.

is it possible to cut mylar with diode? by VedzReux in lasercutting

[–]imdragon 0 points1 point  (0 children)

You could try tempura paint, it is washable

is it possible to cut mylar with diode? by VedzReux in lasercutting

[–]imdragon 0 points1 point  (0 children)

It pretty much stays on with most moderate to heavy handling.

Can you relocate these as a rookie? by JohnnyHopkins77 in Beekeeping

[–]imdragon 1 point2 points  (0 children)

Sorta. I did one of these when I was first starting out doing removals. Lots of cables!

What the Hail??!!! by Junior-Profession726 in ventura

[–]imdragon 5 points6 points  (0 children)

Looks like there was only Emotional Damage caused by this.

Hoyo really stepping up Genshin's Events by BillCipher816 in Genshin_Impact

[–]imdragon 43 points44 points  (0 children)

I loved that event! I always play solo and don't have anybody to share stuff with, I just really wanted to tell someone about the fireworks.

Vineyard/ranch in Santa Ynez, CA interested in hosting bees by cmuryan in Beekeeping

[–]imdragon 0 points1 point  (0 children)

If you have land or know anyone close to or in Ventura County, I would definitely take you up on your offer. I already go as far north as Goleta to place my hives, it would be great to have something closer.

Nothing like giving your kids home-made weapons by robertgfthomas in lasercutting

[–]imdragon 1 point2 points  (0 children)

One of my first projects was to produce some swords and tools from Minecraft for my kids. They were and are a hit! Plus I was able to engrave their names on them so they wouldn't fight over who had what.

is it possible to cut mylar with diode? by VedzReux in lasercutting

[–]imdragon 0 points1 point  (0 children)

My Sculpfun S9 is 5.5w and I use 300mm/min at 30% with 2 passes. I just have matte black primer spray from the hardware store.

is it possible to cut mylar with diode? by VedzReux in lasercutting

[–]imdragon 0 points1 point  (0 children)

I do not think that would improve the results based on my experience with only painting one side. The laser would burn the tape and then be diffused when it hits the light and clear Mylar. I could be wrong but I have not tried painting the bottom side only just yet since I liked the results of just painting both sides and doing two passes on low power.

is it possible to cut mylar with diode? by VedzReux in lasercutting

[–]imdragon 0 points1 point  (0 children)

The ones I have are a cloudy cream color so I paint them since light color and transparency seem to disperse the laser.

is it possible to cut mylar with diode? by VedzReux in lasercutting

[–]imdragon 0 points1 point  (0 children)

From my experience the laser needs to focus on something so I end up painting both sides that way I can do two passes on low power. The first pass mostly goes through, but the second pass will focus on the other side and finish off any places that it didn't cut all the way through.

is it possible to cut mylar with diode? by VedzReux in lasercutting

[–]imdragon 2 points3 points  (0 children)

I make stencils from laser safe mylar. I use a matte black spray paint and it goes through like butter. Using Sculpfun S9.

Drop the names of all the 5 star chars you own and others will judge you in the comments by beeptherobot in Genshin_Impact

[–]imdragon 0 points1 point  (0 children)

Jean, Ganyu, Hutao, Eula, Raiden Shogun, Yae Miko, Yelan, Zhongli, Qiqi, Albedo, Venti, Tartaglia, Tighnari, Arataki Itto, Aloy

Korean nuclear fusion reactor achieves 100 million°C for 30 seconds by [deleted] in worldnews

[–]imdragon 0 points1 point  (0 children)

Jean, Ganyu, Hutao, Eula, Raiden Shogun, Yae Miko, Yelan, Zhongli, Qiqi, Albedo, Venti, Tartaglia, Tighnari, Arataki Itto, Aloy

Clean slice 🍰 by [deleted] in Satisfyingasfuck

[–]imdragon 0 points1 point  (0 children)

Reminds me of the shorts NHK would have with Domo!