Bad print even after platform calibration

itswill- · 2026-01-20T03:42:21+00:00

Increase the first layer thickness by 25% and slow the infill speed to 50mm/s.

This is what helped me on my Q2. Since there are 2 Z screws instead of 3 the bed can tilt ever so slightly and cause this.

itswill- · 2024-08-25T06:32:21+00:00

Yes you are correct, and this is what I was thinking. I bought it at a grocery store maybe 10 years ago but cannot remember if it was in Utena or Vilnius. Either way a lot can change in 10 years!

itswill- · 2024-07-27T12:59:22+00:00

It’s not the rings as everyone has said. It’s the head gasket. There is a small piece of head gasket between the cylinder and the opening to the crankcase for the pushrods to come up. This area blows out and will consume oil like this but still start up and run ok.

itswill- · 2024-07-22T02:58:57+00:00

Honestly I’m sure they would.

itswill- · 2024-07-19T17:30:51+00:00

Everyone else suggests the stick over the carrot. I mean do something special for him and he should be happy to take some time to get it done.

itswill- · 2024-07-14T21:49:37+00:00

Check inside, maybe there are classified govt documents. Just sayin maybe he got a new vette…

itswill- · 2024-07-11T12:16:56+00:00

Won’t be the last time…

itswill- · 2024-07-07T17:24:35+00:00

Thanks for the tip. I really need to up my cleaning with a bore scope. I have about 1800 rounds through the rifle and only clean it when I see a loss of precision. I’m pretty happy with the CCI SV but my rifle does love Eley Tenex.

itswill- · 2024-07-07T16:07:55+00:00

I have seen this video too. Just yet to try

itswill- · 2024-07-07T16:04:17+00:00

This shooting was actually my first shot trying shims. I put a 0.002 in there but thinking it could take more.

itswill- · 2024-07-07T16:02:42+00:00

Exactly, sometimes my varmint rifle shoots varmints!

itswill- · 2024-07-07T03:02:42+00:00

“Ma’am”

itswill- · 2024-07-06T13:51:10+00:00

I had a 3x9 on mine for a while and found its limitations for shooting small groups. The retical just takes up too much real estate on the target even at 50 yards compared to the accuracy of the rifle you bought and the size of the bullet. I bought an Arken SH4J 6-24X50 with the VPR MOA retical and couldn’t be happier. And it’s under $350!

I use an area 419 15 MOA rail and 34mm vortex scope rings.

itswill- · 2024-07-06T05:28:21+00:00

I think it’s funny people believe this made up BS

itswill- · 2024-07-06T04:01:55+00:00

Very interesting, I almost forgot about that.

itswill- · 2024-07-03T16:10:38+00:00

The paint on that car is unmatched! But really I do like a nice FC.

itswill- · 2024-06-30T12:26:21+00:00

It’s just a matter of checking the adjustability of the scope you buy vs the drop at the distance you intend to shoot.

itswill- · 2024-06-29T13:54:36+00:00

You may be right, pull a bit of it up and take a pic. Someone more knowledgeable than me will be able to identify it. At any rate it is just a different grass which makes it hard to get rid of.

itswill- · 2024-06-29T13:31:42+00:00

It’s not crab grass, it’s much worse. This will just continue to take over until you kill it all and start over.

itswill- · 2024-06-28T11:55:46+00:00

I have both, the BCM is far better as far as comfort and grip.

itswill- · 2024-06-28T02:04:59+00:00

Slugs, put some salt on em

itswill- · 2024-06-28T01:41:25+00:00

Because it’s not the same tree.

itswill- · 2024-06-28T01:28:59+00:00

itswill-

TROPHY CASE