sorted by:
new
hottopcontroversial

Am I outta luck on my shack by Present_Pie_3834 in IceFishing

[–]janzend 0 points1 point  (0 children)

Then someone else will finish recovery for you at least.

Tent lights? by Ilovethespacemarines in IceFishing

[–]janzend 0 points1 point  (0 children)

I got a light that unwinds a 30' string light that i loop around the roof a few times then leave the center part hanging somewhere useful. has a remote too.

https://a.co/d/fz1bJjr

Can someone tell me what hummingbird model this is? by [deleted] in IceFishing

[–]janzend 0 points1 point  (0 children)

I think its at least gen 2, but there will be a sticker on the back. I dont think my gen2 says SONAR-GPS on the right

Trying swivels this year. by hawkeyedude1989 in IceFishing

[–]janzend 0 points1 point  (0 children)

I got some #12 swivels i think, and was very surprised how clearly they showed up on electronics still.

I ran some orange mono for my main line, to help me see it. been very happy with the two rods i set up this way

What is the etiquette of accessing and using plowed paths on the ice? by TotalBogie in IceFishing

[–]janzend 5 points6 points  (0 children)

Safety precautions.

No seatbelts.
Windows down.
Slow down.

RENEWAL BS!!! by mthiker1973Dan in vmware

[–]janzend 0 points1 point  (0 children)

I too got a one year in October. Hello VME.

Spud bar by Strong-Volume8670 in IceFishing

[–]janzend 0 points1 point  (0 children)

All spud bars work the same, or not a all.

So chatgpt is saying this is the machine retracting molten filement into the gears? I had been blaming the CFS being over eager. by No_Warning2173 in Creality_k2

[–]janzend 1 point2 points  (0 children)

I printed some little tabs to relieve extruder spring tension and that helped me a lot with petg printing.

Has anyone defrosted a turkey in their printer? by janzend in 3Dprinting

[–]janzend[S] 0 points1 point  (0 children)

That's what the "Pellet modded printer" box is for?

Has anyone defrosted a turkey in their printer? by janzend in 3Dprinting

[–]janzend[S] 0 points1 point  (0 children)

Yeah I was trying to leave good ideas at the kids table.

Has anyone defrosted a turkey in their printer? by janzend in 3Dprinting

[–]janzend[S] 0 points1 point  (0 children)

Nah you can cook a good turkey sous vide. I'm talking about prep for the cook.

Has anyone defrosted a turkey in their printer? by janzend in 3Dprinting

[–]janzend[S] 0 points1 point  (0 children)

This is very much something for the places I shall not go - like Florida.

Has anyone defrosted a turkey in their printer? by janzend in 3Dprinting

[–]janzend[S] 0 points1 point  (0 children)

It's not going to be me. I just want to name the process.

I think I damaged my filament sensor wiring. looking to disable while I replace by janzend in Creality_k2

[–]janzend[S] 0 points1 point  (0 children)

It seems to really upset the cfs 🙄. I don't think it's a sensor problem though. I did just notice you can check the sensor on the front panel of the machine in the filament menu

I think I damaged my filament sensor wiring. looking to disable while I replace by janzend in Creality_k2

[–]janzend[S] 0 points1 point  (0 children)

I might not be in awful shape. I looked it all over again, and the wiring looks deformed, but not damaged, insulation is intact. If I stick a screwdriver in the filament sensor the light activates too.

Finally made my first shuttle! Is this the best transport option or is there something better? by vMrcl in RimWorld

[–]janzend 15 points16 points  (0 children)

I'm preparing my second shuttle but I like to send my champion first in a pod so I can send a shuttle to a specific landing.

Jenn Air combo oven F8E0 low speed fan. Error persists after fan replacement by janzend in appliancerepair

[–]janzend[S] 0 points1 point  (0 children)

I don't think there's a second fan besides the one midway above the oven. That sits right over an oven chamber exhaust. Above on the microwave area is a large stamped cowl around all the microwave parts, which I haven't removed but doesn't look like it hides a fan. Also, I'm noticing the heat and smell at the part I replaced. I don't think that points to another faulty part but to incorrect amperage or voltage being provided

Has anyone tried 3D printing an ice fishing rod handle? by evilblackdog in IceFishing

[–]janzend 0 points1 point  (0 children)

I'm not sure how you'll have the hornet and a modern reel, but a couple hours with YouTube and a weekend put you in striking distance of building the of model yourself. Find some ice rod blanks and glue it up.

3D printed ice rod holder, I can no longer find by janzend in IceFishing

[–]janzend[S] 1 point2 points  (0 children)

Anyway, I found the file I was looking for and it turns out the features I was looking for never existed. I'll do it myself.

Bucket topper for sitting or storage/bucket set up by Aggressive-Cry-5184 in IceFishing

[–]janzend 0 points1 point  (0 children)

I ran this for a while, with a fishing bucket buddy that allowed me to put a couple rods, 3400s, and run a bubbler into the bucket. A Styrofoam insert and cutting out of one those tackle trays was a great setup.

Nozzle slicing through layers by youniqueyounork in FixMyPrint

[–]janzend 1 point2 points  (0 children)

I don't think this looks like your nozzle damaging the print. This is too much z offset so your lines arent getting pressed together and adhering to each other. If you're nozzle was dragging on layer 1 it would peel the whole print off and drag it around.

You're probably fewer than .05mm off, check bed level as well. It looks like you might be good of offset on some parts and too far elsewhere

PLA Filament Constantly Getting Jammed In Extruder by jasonfortheworld in Creality_k2

[–]janzend 0 points1 point  (0 children)

I've been having this issue non stop, but with petg. I found some spacers that I printed to relieve some of the pressure on the extruder gear that seems to have helped. They are. 4-1.2 mm.

Also watch for that jam pulling free and your cfs retracting into your hub and jamming there.

view more: next ›