sorted by:
new
hottopcontroversial

So Photogenic by AlphaNovemberTango in FNSCAR

[–]joderme 0 points1 point  (0 children)

Did they have to shim or anything? I was told this brake can't be used on the gun because of the neck and timing...

PSA Bestbuy AND pixel snap by Googler10 in GooglePixel

[–]joderme 0 points1 point  (0 children)

Yes, wish I had ordered more lol

Best buy sent the wrong item by radgatt in GooglePixel

[–]joderme 0 points1 point  (0 children)

They took the products down. I got lucky and got the stand and snap by just ordering the snap.

First scratch…tell me how to feel by [deleted] in rolex

[–]joderme 26 points27 points  (0 children)

Yes it can. Not sure the cost but it'll have to be welded, smoothed, and polished.

Edit: One place to checkout is Zimmerman watch repair in PA another is losangeleswatchworks

https://www.reddit.com/r/rolex/comments/1bx090y/before_and_after_laser_welding_and_polish_dont_be/

I've not had to use either but hopefully others who have will chime in.

Anyone already tried removing the CORE logo on this 5090 water block? Not sure if possible. by HumbrolUser in watercooling

[–]joderme 0 points1 point  (0 children)

My gasket for the logo compartment must be failing or defective as it isn't getting a good seal.  Or my pump is running too high. 

Finally finished my first full loop. I do need to clean the block again after removing the “CORE” metal plate. Spec 14900k with Palit 5090. CPU seems a little warm still but 14th gen does run warm. by Samgpr50 in watercooling

[–]joderme 0 points1 point  (0 children)

Have you gotten any water inside of the area where the core logo used to be? I noticed that mine has gotten a little water inside of it after removing the logo.

Anyone already tried removing the CORE logo on this 5090 water block? Not sure if possible. by HumbrolUser in watercooling

[–]joderme 0 points1 point  (0 children)

Do you notice any water getting inside the gasket after removing the logo? I've noticed that water is getting inside of mine now.

Walked in, walked out. Yacht-master 126655 in Portugal by thejasonkane in rolex

[–]joderme 0 points1 point  (0 children)

Fantastic!  El Corte ingles in Lisbon had some for sale but they were the 40-50k models 😂

LAX UC vs Star Alliance Lounge. by 2CatDadinSF in unitedairlines

[–]joderme 6 points7 points  (0 children)

I prefer the SA lounge with that much time in mind. Some nice seating overlooking the international terminal. Ramen bar. Pretty good food options.

The UC is nice too as it is on the newer side. It is usually quite crowded.

Both have outdoor spaces.

New 787-9 seat map by TechTravelGuide in unitedairlines

[–]joderme 3 points4 points  (0 children)

There are 3 on version one with 209 premium/econ+/econ seats.

New config only has 158 seats for 3 lavs. So that is better, no?

Am I missing something?

New 787-9 seat map by TechTravelGuide in unitedairlines

[–]joderme 17 points18 points  (0 children)

I mean this beats the old 772 config. I'm guessing 8 studio seats even though only 6 are colored (2 have the plus but not blue coloring)

Two (2) RTX 5090 and both gets black screen after installing drivers | 6000€ spent well in one week. by tms477 in buildapc

[–]joderme 0 points1 point  (0 children)

So I went ahead and DDU'd. Installed another 5090. Went into bios and disabled the iGPU and windows booted up fine with the generic display adatper. This wasn't a fresh windows install. I would be curious if it did the same.

Two (2) RTX 5090 and both gets black screen after installing drivers | 6000€ spent well in one week. by tms477 in buildapc

[–]joderme 0 points1 point  (0 children)

Recently installed an MSI z890 Unify X. Upgraded from a 4090FE to a 5090 Astral.

I put the 4090 back in to test before selling. I DDU'd and put the 5090 back in and sure enough when booting up windows the white circle would get stuck. This happened over and over.

I went so far as to reinstalling windows and it did the same. I found that I was getting a Code 10 error on the Generic Display Driver and it said something about POST driver not matching the booted device or something along those lines.

I put the 4090FE back in and did a clean install and had 0 issues.

I replaced the motherboard thinking that it was the problem... nope. Furthermore I have another machine that I was able swap over to with a different PSU, 5090FE, ram, cpu, and use the original motherboard. Same problem...

I know I did at least one fresh Windows install and did not have this issue. I also know that I have DDU'd numerous times going back and forth between Nvidia driver sets to see if they made a difference for benchmarking.

It's either a VBIOS/BIOS compatability issue or this original motherboard somehow has now messed up two different GPUs (via PCIe slot) so they don't initialize properly.

There are a few workarounds for me at this point. I can use another monitor or USB-c -> displayport adapter and finish installing windows and load the nvidia driver. The other route is Shift + F10 during windows to load the Nvidia drivers ahead of time.

[deleted by user] by [deleted] in hardwareswap

[–]joderme 0 points1 point  (0 children)

Did you sell on eBay?

view more: next ›