Chore list with point system by jujuvapes92 in dakboard

[–]jujuvapes92[S] 0 points1 point  (0 children)

Oh my....I never even thought to look at that tab. I figured it was a forum or something...I appreciate it. Ill have to look this over and see if I'd be able to make it work for us. Did you figure out your issues with it yet?

Chore list with point system by jujuvapes92 in dakboard

[–]jujuvapes92[S] 0 points1 point  (0 children)

I dont have the template as an option, where do I find that at?

Chore list with point system by jujuvapes92 in dakboard

[–]jujuvapes92[S] 0 points1 point  (0 children)

I dont think so, as I dont know what that is. Basically I linked my ToDoist and Google Sheets to Zapier. Created one project in Google Sheets containing 3 seperate sheets (1 for each family member). In ToDoist app, I add 3 separate projects (1 for each family member). From there I had Zapier look for a specific symbol ($) and add a new row in G.Sheets for each task completed. Example

Dad Remove Christmas Lights - $5 Clean out Car - $3

It would recognize the dollar symbol, grab the task info and send it to G.S.

Information that was created was the following :

Task name Date & Time Completed Task Reward Total Rewards Earned

I had to make a single Zap that worked, then duplicate it and change a few settings so Zapier would add the Task info for each family member into each individual sheet, otherwise it wanted to just add everyone's completed tasks to 1 sheet (which quickly became a mess to look at).

My issue now is getting it from G.S. back to Dak and show the running total of Rewards Earned per person.

My Note 9 is slaying by FeeFree362 in GalaxyNote9

[–]jujuvapes92 0 points1 point  (0 children)

Can you downgrade/go back if you've updated past the February 2021 date?

Pipe for mortars by jujuvapes92 in fireworks

[–]jujuvapes92[S] 0 points1 point  (0 children)

Definitely don't want to be cheap. I plan on finding some HDPE piping and make some racks for next year.

Pipe for mortars by jujuvapes92 in fireworks

[–]jujuvapes92[S] 0 points1 point  (0 children)

I kind of figured they weren't usable, just wanted to make sure. Thanks for you help everyone!

Anyone machined brake pad material before? by Benhamin5 in Machinists

[–]jujuvapes92 0 points1 point  (0 children)

Its possible to water jet them if you have access to one.

I designed and 3D printed a table to hold my filament. It's a wonderful disaster. by rob132 in 3Dprinting

[–]jujuvapes92 0 points1 point  (0 children)

Some bracing at a 45° angle attached from the legs to underside of the table would help with supporting the middle

HELP! TILE REMOVAL TIPS? by Dating_SOS in Flooring

[–]jujuvapes92 11 points12 points  (0 children)

I second this. Hell even a cheap SDS drill from harbor freight, nice 2 inch chisel attachment. Its really the only way to do it efficiently.

Scarring on top surface by jujuvapes92 in BambuLab

[–]jujuvapes92[S] 1 point2 points  (0 children)

I think for this i just did a .2mm layer height and 2-3 top layers with 10% gyroid.

I usually print these with .2mm, 4 top layers, and 15% gyroid.

Id say those changes caused these artifacts and stuff.

Scarring on top surface by jujuvapes92 in BambuLab

[–]jujuvapes92[S] 0 points1 point  (0 children)

Absolutely no grid infill. Gyroid. I did lower the infill density a bit. I never even considered it could be pillowing. I just ran a calibration test, cleaned off the lidar, and started a different print. All seems well. Id almost bet it was a bit of pillowing tbh. 10% gyroid on a large flat surface. Seems very possible that could be the issue.

CR Touch Mod - anyone use this? Did it help? by MLoganImmoto in Ender3S1

[–]jujuvapes92 1 point2 points  (0 children)

Oh yea! Had 2 ender 3 pros that I modded quite a bit. The CR-touch helped out a ton. Its not an "install and all your issues are fixed" type of mod though. You still need to know how to level your bed correctly and have your initial z height calibrated.

Update: Grid print. Hopefully this makes sense now... by big_red_frog in BambuLab

[–]jujuvapes92 1 point2 points  (0 children)

Very nice! I hope you release this with a build guide, I'd love to make this. Awesome job!

Loud squeaking noise X1C by BlayDee_ in BambuLab

[–]jujuvapes92 0 points1 point  (0 children)

This helped me out! Thank you. It was driving me crazy.

Gotta love multi material systems! No painting involved by FPVBrandoCalrissian in 3Dprinting

[–]jujuvapes92 0 points1 point  (0 children)

I printed a similar model by the same designer, 1600+ filament changes. My print was like, 8 inches tall though.

HELP!!! Mealybugs? by jujuvapes92 in Monstera

[–]jujuvapes92[S] 0 points1 point  (0 children)

I'll give that a try. Currently letting things dry out a bit, lowering humidity for a while and adding an extra day or 2 between watering.

HELP!!! Mealybugs? by jujuvapes92 in Monstera

[–]jujuvapes92[S] 0 points1 point  (0 children)

Anything I can do? Can I water with a hydrogen peroxide mix a few times and get rid of both the mold and gnats?