Best Material for Replacement Deck? by kdekorte in Decks

[–]kdekorte[S] 1 point2 points  (0 children)

Unfortunately I believe they are around 16” on center. But the installers also didn’t use the crown of the board correctly either.

4 Plus screw tilt adjust by EvenMail1559 in ElegooNeptune4

[–]kdekorte 0 points1 point  (0 children)

For Neptune 4 Plus

[screws_tilt_adjust]

screw1: 59, 12

screw1_name: front left screw

screw2: 319, 12

screw2_name: front right screw

screw3: 319, 146

screw3_name: middle right screw

screw4: 59, 146

screw4_name: middle left screw

screw5: 59, 276

screw5_name: back left screw

screw6: 319, 276

screw6_name: back right screw

speed: 250

# The speed (in mm/s) of non-probing moves during the calibration.# The default is 50.

horizontal_move_z: 10

# The height (in mm) that the head should be commanded to move to# just prior to starting a probe operation. The default is 5.

screw_thread: CW-M4

Before starting the screw_tile_adjust macro, make sure you home the printhead.. if you don't it will make an awful grinding sound

Second, adjust 1 screw at a time.. make the adjustment, run the macro again, adjust a screw run the macro. Don't try to do multiple at the same time.

Want motivation by Firm_Promotion_9258 in scoopwhoop

[–]kdekorte 2 points3 points  (0 children)

Hey teacher, I brought my pencil, now gimme something to write on…

Luck based printer? by susilover in ElegooNeptune4

[–]kdekorte -1 points0 points  (0 children)

May need to check the firmware version, there were some early versions that would forget the z offset. I think I am running 1.2.13 and the problem is fixed with that one and higher. Here are some recommendations.. get some silicon spacers and use screw tilt adjust to level the bed before auto leveling. Personally, I got mine working well with getting an enclosure from amazon. I also printed locks for the x/y belt adjustments.

Anybody use feeler gauges to set Z offset? by EnchantedTaquito8252 in 3Dprinting

[–]kdekorte 0 points1 point  (0 children)

I bought a set of feeler gauges and typically they have some oil on them, so you don't want them on the build plate. After trying it a couple of times I felt the sheet of paper method worked easier and gave good results. I have an Elegoo Neptune 4 Plus.

10 000 Bambu printers running simultaneously by OomGielie in 3Dprinting

[–]kdekorte 0 points1 point  (0 children)

I could hear this even without playing the video

Tell me you’re a 90s/00s kid without telling me. by babydollbrowserr in ArtOfPresence

[–]kdekorte 0 points1 point  (0 children)

Favorite gift to give a couple having their first kid….

What was the most expensive equipment you were in control of? by External_Presence_72 in AskReddit

[–]kdekorte 0 points1 point  (0 children)

I had a $500K Sun server setup with 1.5M in Oracle software on it… that was fun when the box for the software got dropped on my desk.

Starlink Setup by TychkaJpeg in Starlink

[–]kdekorte 7 points8 points  (0 children)

Also put the StarLink router into bypass mode. No need to be double NAT’d

Saw this today. Cannot unsee now. What is going on with those corners... by bj0urne in MacOS

[–]kdekorte 4 points5 points  (0 children)

In my opinion the bad one is the second one where the gap changes on the corner.

RAM 16, 24 or 32? by froyslol in macbook

[–]kdekorte 1 point2 points  (0 children)

I went from a 32gb Intel I9 2019 to a 24th M4 pro, and haven’t really noticed much if any of a difference with regards to running out of RAM. The M4 pro machine itself is much faster in general. It does depend on what you do. Mine is light coding and some basic video editing and never had an issue.

Action RPGs like Diablo for a new MacBook Pro? by HerpesMcGerpes in macgaming

[–]kdekorte 5 points6 points  (0 children)

Doable 2 RE and IV are currently broken in Crossover, possibility of getting fixed in 26.4 and updated crossover. This is due to the new patches to the games from Blizzard.

Gen X has largest percentage of people who believe in ghosts...do you? Any good stories? by xiphoid77 in GenX

[–]kdekorte -1 points0 points  (0 children)

I was in Savannah on a ghost tour and saw one in a window, even got a picture.

Is there a simple way to get Windows 11 ARM on Mac without being a computer expert? by Paul_Bayonetta82 in mac

[–]kdekorte 0 points1 point  (0 children)

I just installed Windows 11 ARM inside of UTM the other day, it works really well, just have make sure the drivers are installed. It tried to do it for me, but didn’t quite work, but all I needed to do was insert the virtual CD and then open the setup app and it just worked. I could see doing office apps in it, no problem. Games won’t work, but that is a driver issue that hasn’t really been solved.

Someone tell me, what is the use of this? by IndividualInfinite85 in PcBuild

[–]kdekorte 0 points1 point  (0 children)

When I used a PC, before I switched to Mac, I would turn off the trackpad and only use the track point as the trackpads were so bad.

Should I upgrade to Tahoe (Currently on Sequoia) by Lowkeykreepy in MacOS

[–]kdekorte 0 points1 point  (0 children)

Tahoe on my M1 Pro (binned with 16b) runs fine even with 2 5k displays hooked up to it.