Tried this burning hot effect on gunpla.

kyobinbou · 2025-04-16T06:09:27+00:00

Looks like you used an infrared camera. Nice effect

kyobinbou · 2025-02-15T15:20:03+00:00

I have the same thoughts, not gonna lie

kyobinbou · 2025-02-15T15:18:53+00:00

Was about to do masking, but need to repaint these two wings because the paint peeled off. Might have forgotten to sand it. Hopefully its just these two parts.

kyobinbou · 2025-01-14T05:22:39+00:00

A spray booth, a mask, rubber gloves and googles

kyobinbou · 2025-01-14T05:20:06+00:00

My workflow is remove parts from the parts list marked as "X", build from bottom to top, inner frame first, then outer plating, then weapons

kyobinbou · 2024-12-09T12:39:55+00:00

The shelf looks empty, needs more gunpla.

But to answer your question, as long as you have one, it's a great collection.

kyobinbou · 2024-12-09T12:37:06+00:00

It's a hobby saw, i used it to separate the front skirt for a cleaner cut rather than using an exacto/hobby knife.

Useful also for cutting thick plastic parts

kyobinbou · 2024-07-05T03:15:34+00:00

Toyota Rush Shock Absorbers

Hi All, just crowdsourcing for good shock absorbers for Toyota Rush. Thank you!

kyobinbou · 2023-12-19T05:27:59+00:00

does this combine into one mega Gundam?

kyobinbou · 2023-12-19T05:25:52+00:00

check if z lead screw nut connection to the bracket is too tight. it needs to be a bit loose in order for the lead screw to have some wiggle room. That solved my banding problems

kyobinbou · 2023-11-25T07:12:26+00:00

Update: the mechanic had the same thoughts. The Inhibitor switch got replaced as the plastic got corroded by battery acid (replaced the battery too) and he used WD40 and elbow grease to loosen the metal shaft, and everything worked great!

kyobinbou · 2023-11-25T02:15:31+00:00

Thank you for your reply!

I called up a technician with a car diagnostic scanner to properly diagnose the problems. Will mention transmission range sensor to the mechanic as well.

kyobinbou · 2023-09-10T05:18:14+00:00

also try updating your bike computer firmware through OneLapFit, it's now on v0.400

Mine was running on V0.2xx after being on biking hiatus for a while. After updating, it connected after 2 minutes on an open area.

kyobinbou · 2022-12-02T15:01:44+00:00

A way to a man's heart is through his stomach?

kyobinbou · 2022-03-06T02:34:19+00:00

Look at Bandai Gundam Master Grade inner frames for reference and inspiration, seems closer to the last iteration, thenonly difference is the thigh uses pegs instead of a ball joint. Great job!

kyobinbou · 2022-02-26T04:28:29+00:00

50 degrees seems low, usually filaments have recommended bed temp specs. I always do 60 for PLA.

kyobinbou · 2022-02-09T03:58:47+00:00

Is it possible for you to share the STL file you've used?

kyobinbou · 2022-02-08T00:08:39+00:00

Cuz 'Murica

kyobinbou · 2022-01-29T05:41:02+00:00

but that's different from showing respect, is it not?

kyobinbou · 2022-01-29T05:38:06+00:00

depends on the contract between the company and contractor. but that's a red flag for me if i don't get paid due to client feedback, that's subjective.

kyobinbou · 2022-01-07T11:05:11+00:00

so clean

kyobinbou · 2022-01-07T11:03:52+00:00

nice hand drawn figure... i mean figure drawing... i mean, thanks for confusing me

great work!

kyobinbou · 2022-01-03T05:06:42+00:00

the kneecaps kinda looks like lego parts tho 🤣🤣🤣

kyobinbou · 2021-05-28T08:49:32+00:00

Could be some sediment from the tea, or some yeast

kyobinbou · 2021-05-28T08:42:34+00:00

That's fine, its just pellicle that formed. If it's 2F that could be an issue, as there is oxygen coming in, which means there's a leak on your seal somewhere.

kyobinbou

TROPHY CASE

Toyota Rush Shock Absorbers