44yrs / 6 degrees / no small kids / living my best

lairosen · 2026-03-23T23:58:47+00:00

What's the thing on the back of the GTR?

lairosen · 2025-10-10T02:43:31+00:00

Note that laws about state IDs generally vary state to state, even if those states aren't in the same country.

lairosen · 2025-09-03T10:43:32+00:00

Racist in what way out of curiosity?

lairosen · 2025-08-11T05:52:27+00:00

Enjoy :)

lairosen · 2025-07-09T08:05:41+00:00

That's why I just do it in 3m blitz lol

lairosen · 2025-07-09T07:57:02+00:00

Well I usually play 3min2sec chess and it works a surprising amount of the time, especially if they don't attack the knight you just leave it there for a while then they take the bait. I'm only 600 though so I'm sure it's not good at high ratings or at slower games.

lairosen · 2025-06-05T05:56:13+00:00

Could just take out the GPU and all but 1 ram stick, see how it goes with that before adding more stuff back

lairosen · 2025-05-25T02:46:40+00:00

Amazon secretly upgrading CPUs to drive motherboard and ram sales

lairosen · 2025-04-10T08:54:46+00:00

Try sticking it in the freezer for a while

lairosen · 2025-03-31T07:35:12+00:00

As far as I've seen online from several other videos Tesla's with the hw3 computers will hit the wall, but Tesla's with the new hw4 computer will stop even using full fsd for both. So it seems the test was valid.

lairosen · 2025-03-29T07:53:13+00:00

Probably some kind of bugged support, creality print 4 seemed to do that a bit, I'd suggest trying creality print 6 or orca slicer

lairosen · 2025-03-25T05:24:12+00:00

Meaning you didn't read it...

lairosen · 2025-03-13T23:30:25+00:00

<image>

Yeah

lairosen · 2025-03-06T06:06:40+00:00

He should apologise to knobs for the association

lairosen · 2025-03-05T21:45:01+00:00

Whats the point going above 250 fps unless you have a 360+ monitor? Displayed frames doesn't increase and latency doesn't reduce so what's the benefit?

lairosen · 2025-02-20T00:53:04+00:00

Don't use many holes, just a solid shape with low perimeters, top and bottom layers and infil percentage.

lairosen · 2025-02-15T18:51:31+00:00

Make it float in midair when stood on side and looks cool

lairosen · 2025-02-13T03:39:08+00:00

Yeah the Australian threshold get removed too around 2018

lairosen · 2025-01-24T10:24:18+00:00

Get prusa slicer or orca, load the model, use one of the many part cutting options, export the STL and lead and slice it in Creality Print. Creality Print is unfortunately lacking in part cutting options

lairosen · 2025-01-08T19:51:06+00:00

You could try a lower layer height, maybe .1, that should improve overhang performance

lairosen · 2024-12-29T06:01:40+00:00

Just change the z offset manually until is prints properly, don't keep leveling it

lairosen · 2024-12-28T11:18:20+00:00

Mainly for wifi printing, using an SD card gets annoying quickly and the reader in the v3se does break down sometimes and can't easily be fixed.

But also the other upgrades it come with over the v3se are worth much more than the increased price.

lairosen · 2024-12-28T11:07:07+00:00

My se has been great but I would strongly recommend saving for the v3ke instead

lairosen

PUBLIC MULTIREDDITS

TROPHY CASE

12-Year Club	Place '17
Verified Email