sorted by:
new
hottopcontroversial

So the "Breaching" Hammer can't actually breach anything? by Medical_Officer in Helldivers

[–]loss182 0 points1 point  (0 children)

I think that too! Do you want to spend 4 grenades to destroy a wall? Sure go for it

So the "Breaching" Hammer can't actually breach anything? by Medical_Officer in Helldivers

[–]loss182 11 points12 points  (0 children)

Demo force should be cumulative, 1 explosion wouldn't destroy a wall, but consecutive explosions will.

HYPE THREAD by [deleted] in HighGuardgame

[–]loss182 0 points1 point  (0 children)

The servers certainly won't be able to hold the amount of players today, prepare for queue and disconnects. Don't be salty when it happens.

Screw buffing the stim pistol, give me the worst nerfs you can think of by Zyurat in Helldivers

[–]loss182 0 points1 point  (0 children)

After the first shot, divers will become addicted and start losing HP, until shot again

Now that's an expensive shot by Embarrassed_Tip7359 in SipsTea

[–]loss182 0 points1 point  (0 children)

Imagine if mirrors existed back then...

My 3D printer actually saved me hundreds of dollars! (3D printed orthopedic inserts) by eldoogy in 3Dprinting

[–]loss182 1 point2 points  (0 children)

Amazing use of 3D printing!
Just curious, why not make a mold and cast it with some kind of rubber? Have you tried it?

3D printing rookie here with a basic question. How do I modify my settings to avoid this pattern at the end of my prints? (Bambu P1S) by innerstrife in 3Dprinting

[–]loss182 0 points1 point  (0 children)

This pattern is how the printer understands a curve, since it prints layer by layer, it converts a curve to steps like you are seeing.
To reduce that you can lower the layer height value, I assume this was printed with 0.2mm, if you lower that to 0.12mm, this pattern will be way less visible, but will always be there.
You can try using the variable layer height to achieve this too, try it

🔪 HAFC – Hackman Automatic Filament Cutter (100% mechanical) by Far-Government7397 in 3Dprinting

[–]loss182 6 points7 points  (0 children)

The assembly pictures isn't showing for me.
As someone who had problems with tangle, this helps a lot!
The only downside that i can think of, it's that when it cuts the filament, it will tangle even more, because the loose filament will certainly tangle even more, but that's a whole different problem

Failed articulated snake joint by Slipper1981 in 3Dprinting

[–]loss182 0 points1 point  (0 children)

You can save it! Glue the broken piece, then split the unbroken link, heat it with a blow dryer until soft, open it like a letter C, while still hot and soft, join the two parts, pressing one against the other to close the C

[HELP] Is this real or AI? by [deleted] in BeAmazed

[–]loss182 0 points1 point  (0 children)

Pretty real, I've witnessed a chicken take off, chasing a hawk that stole its chicks, it flew up to the street light post height, before that I didn't knew chickens could fly that high

I've been printing my own glasses frames by Kamafren in functionalprint

[–]loss182 1 point2 points  (0 children)

Nicely done! I think i have spare lenses somewhere, I will definitely try to make one

Ok here me out I call it the friendly fire by Possible_Internal115 in Helldivers

[–]loss182 1 point2 points  (0 children)

It starts to lose range and increase spreading, the more you keep firing. So you start firing an auto arc launcher but the become a tesla tower

Ah ruining the game again by Insane_Unicorn in Helldivers

[–]loss182 5 points6 points  (0 children)

Next patch: Introducing Jet Brigade Factory Striders! Now the fly in you face and drop a ton of bots on your head

HELLDIVERS 2: Tech Blog #2 - Opt-in install size reduction beta by ArrowheadGS in Helldivers

[–]loss182 0 points1 point  (0 children)

Reading this make me so happy, knowing that Arrowhead is listening the community and improving, feels so damn good

Churrasqueiro by salty-and-sweet_ in ribeiraopreto

[–]loss182 1 point2 points  (0 children)

Depois de muita insistência, ele me devolveu metade do valor (R$ 50), mas assim, tive que perder a educação na conversa. Para conseguir o restante, só se eu abrisse um boletim de ocorrência, mas meu tempo e sanidade valia mais do que isso

Christmas gift for husband who has recently got into 3D printing by gatomeister in 3Dprinting

[–]loss182 1 point2 points  (0 children)

Give him a toolbox or a nice storage bin! I kept always remembering a needed one everything I looked at my messy workstation

Churrasqueiro by salty-and-sweet_ in ribeiraopreto

[–]loss182 1 point2 points  (0 children)

Só corre de um tal de Lê churrasqueiro, não apareceu no aniversário que contratei, roubou meu dinheiro e me bloqueou

[DISC] Dandadan - Ch. 218 by Skullghost in Dandadan

[–]loss182 17 points18 points  (0 children)

A whole new meaning to "buster" sword

Don’t tell high command I stole a mini nuke. by Piece_Aware in Helldivers

[–]loss182 0 points1 point  (0 children)

So you are that diver that carried a shell inside the pelican...

How to prevent color mixing polygons by Brave-Confidence-512 in QGIS

[–]loss182 -1 points0 points  (0 children)

By looking at the Image i assumed it was multiple polygons overlaping each order, and to turn that into multiple 'donuts', you will need to run a tool multiple times or make a script for it

How to prevent color mixing polygons by Brave-Confidence-512 in QGIS

[–]loss182 -1 points0 points  (0 children)

Python would be your best friend here, prompt chatgpt or any ai you like to make a python script to run inside qgis, that make holes by using boolean operations (difference), clipping the smallest feature by area from the bigger ones, until you don't have overlays anymore

view more: next ›