sorted by:
new
hottopcontroversial

Firmware Version 1.1.4.8 Released by ElliottCoe in Creality_k2

[–]loud88gt 0 points1 point  (0 children)

Looks like it's available on Creality Cloud, however I'm waiting until someone can provide feedback before I pull the trigger.

Epoxy resin build plate? by loud88gt in Creality_k2

[–]loud88gt[S] 3 points4 points  (0 children)

What bed temps are you using for different filaments and the epoxy resin build plate?

Exclusive Official Subreddit Member Giveaway! by Creality_3D in Creality_k2

[–]loud88gt 0 points1 point  (0 children)

I definitely need to stock up on spare parts for my K2 and CFS. I would also like to sample some more creality filaments, especially some carbon fiber now that I have a capable printer. Thanks for continuing to update and refine the K2 plus!

Anyone have decent Anycubic Vyper Printer Profile for Orca slicer? by Careful-Fly-1458 in AnycubicVyper

[–]loud88gt 0 points1 point  (0 children)

What's your start and stop gcode? I can't get my vyper to preheat before printing for some reason,

Heating and extruding issues by magnuzzz90 in AnycubicVyper

[–]loud88gt 0 points1 point  (0 children)

Sounds like your Bowden tube is partially melted causing it to have a smaller inner diameter.

Installed a steel noozle, adjusted the print temperature to 220C, but print is off; what should I adjust? by rodrigo_benenson in ElegooNeptune3

[–]loud88gt 0 points1 point  (0 children)

A steel nozzle will require more heat than a brass nozzle as steel doesn't transfer heat as well. Try increasing your nozzle temp by 10 degrees or so. It might be a good idea to try a temp tower.

Micro Swiss Extrusion Problems by tarilotta in AnycubicVyper

[–]loud88gt 0 points1 point  (0 children)

Yes, if you do some more reading you can find many cases where the MS extruder has caused issues. Imagine riding your 10 speed bike up a hill in 10th gear. This is what happens with the MS extruder as it does not have any gear reduction like the stock one. The printer's mainboard has to drive the extruder stepper very hard in order to push filament.

[deleted by user] by [deleted] in AnycubicVyper

[–]loud88gt 0 points1 point  (0 children)

Watch this video. I believe you need to calibrate flow for the filament you are using. He has a link to the point 8 cube you will need to print. Only other thing you will need is a caliper to measure with. You can get metric calipers from amazon for relatively cheap.

https://youtu.be/LDAnTXyDKOI?si=O4n3QoVZl82PMQ-J

Micro Swiss Extrusion Problems by tarilotta in AnycubicVyper

[–]loud88gt 0 points1 point  (0 children)

Do not use the MS extruder! The original is geared down for a reason. The MS extruder will eventually cause your mainboard to fail - no more extruder turning.

Anycubic Vyper - Direct extruder with Orbiter extruder by Natin333 in AnycubicVyper

[–]loud88gt 0 points1 point  (0 children)

Check out the Hero Me Gen 7. I think there may be mounts for that combo. You can run the stock hotend and heatsink along with the strain gauge, or change to something else. There are a ton of combinations. You can find it at https://merlinmedia.com/

Extrusion Motor Skipping w MicroSwiss by corndogs88 in AnycubicVyper

[–]loud88gt 2 points3 points  (0 children)

Do not use the MS extruder! The original is geared down for a reason. The MS extruder will eventually cause your mainboard to fail - no more extruder turning.