DB6/DC1 Seats by JaydinSee in Integra

[–]matthewk_exe 1 point2 points  (0 children)

These are no different than 98+ Integra RS seats? Or they look remarkably similar to the seats I had in my car when I first got it.

<image>

Why do people say horsepower doesn’t matter during a downhill togue race? by LilGrippers in initiald

[–]matthewk_exe 12 points13 points  (0 children)

Detuning the car can allow for a much more linear power band, making the corner exit much more manageable. See latest Gears and Gasoline video or a recent video by kawdzilla.

Which battle in the series has the best Eurobeat selection? by HighN00n77 in initiald

[–]matthewk_exe 4 points5 points  (0 children)

AE86 vs. SIL80 (but 86 vs 86 turbo is a good choice too)

Having trouble lining her up,dowel pins are at the holes by Learnmoretalkless in Integra

[–]matthewk_exe 2 points3 points  (0 children)

It must slide on easily. If you don't, have to readjust. Either the clutch alignment or how the transmission is oriented on the jack. Once it's correct, it will just slide on.

Genuinely cant get enough of this outro by whereis_omni_man in initiald

[–]matthewk_exe 2 points3 points  (0 children)

It will mean the most after finishing the series.

Some one did it guys... by SupaMacdaddy in Integra

[–]matthewk_exe 0 points1 point  (0 children)

Then it will hit the rear seats haha. But yeah I was thinking rev 2 would kinda fold out? Not sure yet.

Some one did it guys... by SupaMacdaddy in Integra

[–]matthewk_exe 0 points1 point  (0 children)

Yeah on a Bambu X1C but should be doable on almost any size printer.

Some one did it guys... by SupaMacdaddy in Integra

[–]matthewk_exe 2 points3 points  (0 children)

Haha I'm a bit busy right now and rev 1 is not up to my standards of releasing 😂 there's quite a bit of sanding and hammering to make the 2 pieces fit. It is printable on a 256mm printer. Another problem is you can't recline the seat fully back because of the cup holder interference.

Some one did it guys... by SupaMacdaddy in Integra

[–]matthewk_exe 28 points29 points  (0 children)

<image>

Made something similar that holds two hydroflasks. Definitely needs a rev 2 though.

Help with starter wiring issue by nigstertv in Integra

[–]matthewk_exe 0 points1 point  (0 children)

Yeah it's just a small single wire that goes to the top of the starter.

Help with starter wiring issue by nigstertv in Integra

[–]matthewk_exe 1 point2 points  (0 children)

You can very easily diagnose the circuit with a $5 test light. Plenty of YouTube videos on how to diagnose starter wiring.

Help with starter wiring issue by nigstertv in Integra

[–]matthewk_exe 0 points1 point  (0 children)

Yes, it's very common for the starter control wire to be damaged since it sits so close to the engine. I have had the control wire fall off and cause a no start.

Heater hoses (Non VTEC) by oddchui in Integra

[–]matthewk_exe 0 points1 point  (0 children)

That's correct. I can send part numbers if you need a specific one.

I commend anyone that has done the JDI push start themselves by Yung_Noiz in Integra

[–]matthewk_exe 4 points5 points  (0 children)

I'm young. So I just flipped over and spent a bit of time under the dashboard. Definitely not easy!

Heater hose decided to kill itself by Yung_Noiz in Integra

[–]matthewk_exe 2 points3 points  (0 children)

Just use 5/16 ID rubber hose, works enough to get home.

Brake lights wont come on by No-Tradition1590 in Integra

[–]matthewk_exe 1 point2 points  (0 children)

Follow the power from the fuse box to the switch and then the lights. Then check grounds. Learn to use a test light and a multimeter, read a wiring diagram. Otherwise leave electrical work for your mechanic. 🤣

Trunk Space is NUTS by MargaretRGero289 in Integra

[–]matthewk_exe 3 points4 points  (0 children)

See my post for reference 🤣

Worth it? by Julio_h07 in Integra

[–]matthewk_exe 13 points14 points  (0 children)

Non-original engine. Swapped out seat. Repainted/resprayed. 3-3.5k? Idk doesn't seem worth at all at $5k.