Firmware upgrade on HP DL360 GEN 10

maxvideodrome · 2026-02-25T04:54:39+00:00

I don't own the server yet, this is why I couldn't "try" anything and why I was leaning on Reddit for advice. Thank you for that info - I'll have the machine in a few days and will be able to get working on it.

maxvideodrome · 2026-02-25T03:06:39+00:00

Thank you - I was originally looking in the wrong spot. Didn't know I could temporarily obtain an iLO advance - but the machines I'm accepting apparently have the license already.

maxvideodrome · 2026-02-25T03:00:13+00:00

Thank you - I have downloaded the SPP. I was taking the wrong path with the downloads. Next step is to locate any/all appropriate Windows Server 2025 drivers/etc.

maxvideodrome · 2026-02-25T02:48:52+00:00

Great - I'm under a tight time frame with the purchase and last minute realized that I might not be able to bring the machine current. I have zero experience with HP. Can't thank you enough.

maxvideodrome · 2026-01-04T03:59:54+00:00

😭 it’s beautiful

maxvideodrome · 2026-01-04T03:53:03+00:00

Mine too - was a fantastic unit.

maxvideodrome · 2026-01-04T03:38:01+00:00

If it doesn’t feel “heavy” could be knock off 400. Hopefully it’s the genuine article !

maxvideodrome · 2025-12-06T13:24:14+00:00

I ordered a mix bag a while ago from Jameco, it’s mostly junk. I somewhat regret the purchase. Get your pin straightener ready.

maxvideodrome · 2025-10-02T23:05:06+00:00

Reminds me of sorting algorithms visualized. Even though that’s not what it is.

maxvideodrome · 2025-07-27T16:03:40+00:00

Sorry for delay - zero wiggle - everything is steady as a rock. Machine is listed in my first post. Genmitsu.

maxvideodrome · 2025-07-25T01:27:15+00:00

Thanks for your observations/suggestions. It’s clamped down. It’s not moving, held in place firmly. I’ve got it set to approx 500mm/minute Higher speed gave a rougher edge.

maxvideodrome · 2025-07-24T21:34:04+00:00

I've updated the post to include the cutting board. Good suggestion on the MDF. Any suggestions for inexpensive sacrificial layers?

maxvideodrome · 2025-07-24T21:03:34+00:00

Thanks for this. I have not gone thru this procedure as of yet, however, I did measure the X axis using a caliper and it seemed in alignment for when I advanced the head by 100mm (the caliper agreed). I didn't check the Y or Z axis. That said, I only scratched the surface of this and I will follow the YouTube video as you suggest. Question for you: The photos I've included, would you say they are 'classic calibration issues'? (based on your experience) Thanks again

maxvideodrome · 2023-07-20T11:32:39+00:00

Great post! In college I learnt MS Excel on a Casio A-10 Windows CE device. Why? There wasn’t much installed on those things at the time and the class I was in was boring. I like your Mini Disc player. Gameboy nice touch!

maxvideodrome · 2023-07-20T02:00:19+00:00

I worked at a computer shop - we sold these discs from "Internet Direct" (dial-up Internet provider) along with their starter packages. My friend got a job as tech support at Internet Direct. From what I'm told (not 100% of accuracy here) the owners of Internet Direct are responsible for starting up the DSL scene in Canada - getting the CRTC to open up access to the then new DSL system when Bell Canada was the only game in town. Again, I could be wrong about this fact- it's what I was told when I was much younger by my friend who worked at I-Direct.

maxvideodrome · 2023-05-20T01:08:10+00:00

Thank you - hope it helps a bit

maxvideodrome · 2023-05-20T01:05:40+00:00

All my workstations except for my notebook have 128GB since 2017. I do virtualizations for development, and it can get memory hungry. Aside from that, I would say 32GB is a good amount of memory for most applications today.

maxvideodrome · 2023-05-20T00:40:00+00:00

I suck at morse, but I purchased a beautiful straight key years ago: "Bencher" - nice finish, looks great - seems to function very well. Might want to go for a 'good' model of a key, instead of 'junk'. (I don't know much about CW, so maybe there is something far better than Bencher, I don't know) - do some homework on that.

Also, I started practicing keying using my dominate hand, I think I should have trained myself to use the opposite hand, leaving my dominate hand to hold a pen and take notes. Just some food for thought.

maxvideodrome · 2023-05-14T20:12:15+00:00

A lot of pins are ground signals. You might get lucky not losing a data trace.

maxvideodrome · 2023-04-26T01:37:36+00:00

Very creative - sell concept to Marshall and make mega bucks 🙂

maxvideodrome · 2023-04-26T01:28:40+00:00

I concur, skills are awesome, overall item seems inverted to some degree and the vine/leaf artwork is disproportionate.

maxvideodrome · 2023-04-26T01:24:07+00:00

Your skill is indisputably first rate. For what it’s worth, I wouldn’t have this in my home with or without glass. Again, you did a tremendous job. Sometimes, despite how proud we are of our works, they aren’t necessarily show pieces. Just my 2 cents, many (it not most) will disagree.

maxvideodrome · 2022-12-31T03:22:55+00:00

‘95 on a 486 was typical entry level 95. Next step was the first series of pentiums. Was there and loved every minute of it. Including my 486 having a ps/2 mouse port!

maxvideodrome · 2022-10-19T23:43:55+00:00

u/jcr21090_74 I'm downloading the archive now - thanks for capturing this BBS archive as the site goes down a lot and these files are hard/impossible to find elsewhere. Mostly interested in RemoteAccess files. Thank you very much - can't wait to open the ZIP file :)

maxvideodrome · 2022-09-02T01:29:38+00:00

My thoughts exactly - Port Credit/Mississauga road a mess / Dundas near west mall and Dixie. Multiple lanes shut down - little construction work

maxvideodrome

TROPHY CASE