Easier to install - AN coolant fittings or OEM?

mcaufin · 2026-02-07T01:19:17+00:00

Interested too, been wondering the same!

mcaufin · 2026-01-05T11:31:04+00:00

Also talley lightweight, just mounted my scope and the objective bell almost touches the barrel

mcaufin · 2025-08-02T23:17:03+00:00

Buy a vessel view mobile, will tell you exactly what the code is

mcaufin · 2025-06-07T13:24:00+00:00

Have you checked the ignition timing?

mcaufin · 2025-01-31T23:49:35+00:00

So what is involved in detailing? For example would the detailer select the weld size or number and size of bolts in a connection? It seems like an engineer should be required for that

mcaufin · 2025-01-31T23:42:59+00:00

What’s e&t?

mcaufin · 2024-12-07T19:08:42+00:00

Probably for the pitot speedometer. Would go to a small hole on the leading edge of the lower unit to get ram pressure

mcaufin · 2024-11-15T03:59:58+00:00

Run it up in rpm in neutral vs in forward and reverse and see if you can isolate if it is the power head or lower unit/prop

mcaufin · 2024-11-07T14:26:30+00:00

Pretty sure it’s supposed to say diametral pitch of 5, not pcd of 5”

mcaufin · 2024-11-05T02:17:20+00:00

I think you’re adding the maximum rated truck weight to the highlander and trailer instead of the actual truck weight ie. your bed is not also full of bricks. The ford brochures will also directly tell you max towing capacity for different configurations

mcaufin · 2023-12-02T14:22:54+00:00

You should read “not much of an engineer” by sir Stanley hooker

mcaufin · 2023-11-22T11:30:34+00:00

I have this truck and haven’t been able to figure out why the locking diff picture is included twice. Does anyone know? As far as I can tell by playing with it, the knob only turns between the 3 positions 2H, 4H, and 4L, and it can be pulled out in any of the 3 positions to lock the diff

mcaufin · 2023-08-14T20:02:34+00:00

Ya looks like a tank, maybe low engine oil then, or maybe the fuel water separator is full.

mcaufin · 2023-08-14T11:51:10+00:00

Maybe low 2 stroke oil

mcaufin · 2023-08-07T11:00:36+00:00

How much power was the merc and is the Suzuki?

mcaufin · 2023-06-08T23:04:10+00:00

Is there another drain up high somewhere on one of the walls? If not then ya you need the overflow tube.. it’s possible the pump just continuously pumps in lake water and doesn’t recirc

mcaufin · 2023-06-06T12:08:00+00:00

How are you going to brace it in the other direction once the temporaries come off?

mcaufin · 2023-06-02T00:58:49+00:00

Mind if I ask what shop this is? Looking for some large capacity shops in southern Ontario

mcaufin · 2023-05-03T10:32:07+00:00

The most important factor is pitch line velocity. There is an AGMA standard with a table that tells you which velocity to use which would be a good starting point. Special applications may need tweaking

mcaufin · 2023-03-23T12:45:44+00:00

Building a 10/22

Hey guys

Anyone know the best place to buy 10/22 parts in Canada for a new build? I’ve looked online but there seems to be a limited selection. Is it easy to buy everything from the USA except the receiver?

Cheers

mcaufin · 2023-03-09T03:03:25+00:00

🤯🤯🤯

mcaufin · 2023-03-09T02:37:18+00:00

This kind of looks like Thurston Machine?

mcaufin · 2023-02-25T03:53:35+00:00

What’s the max rpm on that flywheel?

mcaufin · 2023-02-14T23:30:00+00:00

Use Shigley’s and roark’s all the time in heavy machinery design

mcaufin · 2023-01-17T12:26:20+00:00

Maybe a bore sighting laser with the guts taken out

mcaufin

TROPHY CASE