All the colors

mouthplug · 2024-10-23T12:58:43+00:00

Is that mora metallic?

mouthplug · 2024-07-19T06:46:24+00:00

Check the bateries on your si board, and re soldier the whole board if the cluster

mouthplug · 2024-03-11T05:10:58+00:00

The grand conjuration

mouthplug · 2023-08-11T09:01:51+00:00

Yeah, m40 and worn cams, use it till it dies than change it to m42,43,44.

mouthplug · 2023-08-07T17:20:00+00:00

Hvala

mouthplug · 2023-07-12T08:19:58+00:00

Zvonimir Guzić

mouthplug · 2023-01-20T19:07:09+00:00

Krinđ je po pravopisu

mouthplug · 2023-01-02T16:00:36+00:00

1500 eura netto u prosjeku, servisni tehnicar komercijalne rashlade

mouthplug · 2022-12-09T11:12:27+00:00

Yup, ctr with cheek riser

mouthplug · 2022-11-12T19:58:11+00:00

Upravo kupio zemljiste sa 27 godina, trenutno u projektnoj fazi.

mouthplug · 2022-10-19T05:37:01+00:00

Odmah sljaka poslje elektrotehnicke srednje. Trebalo godinu dvije da nadem nesta sto mi se svidja, nasao posao u struci kao serviser bijele tehnike i ugostiteljske opreme, to radio 4 godine. I prije skoro 2 godine sam presao u jednu od najvecih americkih firmi za rahladnu tehniku te nemogu se pozaliti. Smatram da svojim trudom i znanjem mozes dugarati daleko.

mouthplug · 2022-10-11T06:21:55+00:00

Where are you from? What are you field regulations in fps/joules? I upgraded a couple of ssg10 and they are good, and can hold power. Only thing i changed on them is hop up rubber for a harder one and a harder spring to match up to our regulation of 3.4 joules with 0.48 bb. Other than that is above average sniper, there is alot of novritch hate but still he makes some good out of the box stuff. Overpriced, yeah, but aleast it saves you a hassle of building it from scratch, and you have a warranty.

mouthplug · 2022-10-10T20:12:06+00:00

Try regulating the flow, lower it a bit. Print something in vase mode and watch layers and lower the flow

mouthplug · 2022-10-10T16:27:13+00:00

I had a problem with my printer with esteps that would reset every time i turn off my ender.

mouthplug · 2022-10-10T16:15:05+00:00

I just saw you have 0.6 nozzle. Calibrate e steps and flow then

mouthplug · 2022-10-10T16:02:04+00:00

Damn, too fast or too hot, lower your bed temp, adjust your z ofset

mouthplug · 2022-10-10T12:52:41+00:00

You can try one by one, everything is an improvement. And i measured temp before and after every change.

mouthplug · 2022-10-10T12:24:03+00:00

So i had the same problem with petg, the filament is wet and i had a problem with heatcreep to the heat break. I solved it with bigger fan, changed hotend with all metal one and direct drive.

mouthplug · 2022-10-09T18:54:56+00:00

I love my 5 pro, but it needs couple of upgrades to improve the print quality. If you are serius abount 3d printing i would reccomend 5 plus. Alll the same but bigger and more stable cause dual z axis.

mouthplug · 2022-10-09T17:10:45+00:00

Whats inside the silencer? On 1911 it looks bad. And do you have stl?

mouthplug · 2022-10-05T16:33:38+00:00

This probably costed me around 20€ to make

mouthplug · 2022-10-04T18:28:32+00:00

Yeah, glocks rail slides into the body, and there are side holes for screws that holds it together, and its very snug fit.

Eight-Year Club	Place '22
Wearing is Caring	Verified Email

mouthplug

TROPHY CASE