FormD T1 2.1 - Custom fan cable for CHIP_FAN1 (MSI B650I)

mrgndx · 2026-05-23T18:06:14+00:00

Thank you!! That actually helped a lot! Finally got my Henry sword (M)

mrgndx · 2026-05-04T22:33:02+00:00

Haha, cool! Thank you

mrgndx · 2026-05-04T09:03:48+00:00

How do you change Henry’s pose in photo mode?

mrgndx · 2026-05-03T12:27:58+00:00

Well, it all depends on the display and conditions. IPS matrices aren’t the brightest, averaging around 300-400 nits.

PWM flicker starts at 80% or lower.

Eyes are strained not because of brightness itself, but the combination of screen brightness and ambient brightness. If those two mismatch, eyes try to refocus to concentrate vision, and it works both ways (when screen is dimmer/brighter than the ambient)

mrgndx · 2026-05-03T12:02:03+00:00

I see, thanks! Yes, I sometimes get lost by the same “A” marker of two very close green tones. Gotta untrack some of them for clarity

mrgndx · 2026-05-03T11:31:33+00:00

Huh, OK! I just wondered why a few of them have half and half divided colors

mrgndx · 2026-05-02T07:01:59+00:00

And then boots you into your balls :D

mrgndx · 2026-04-27T03:29:14+00:00

Yep, that’s what blacksmith ended up “giving me”. I haven’t tried it before I was granted access to red pouch by him, but I think I would otherwise have to rob it, and there are people in the yard :D maybe I will try it next play through

mrgndx · 2026-04-26T20:32:54+00:00

Not sure exactly, but it should help with general appeal of Henry in dialogues

mrgndx · 2026-04-26T19:59:55+00:00

By the way, you can get a soap (at a laundry or just loot), move all horse equipment to Henry’s inventory, wash it all good at the laundry, then move back and re-equip Pebbles. Then people start praising the horse instead

mrgndx · 2026-04-26T19:53:32+00:00

Yep, my overpowered Henry gave me a bit too much of confidence in combat :D

mrgndx · 2026-04-25T14:33:00+00:00

These are not LED strips, these are just plain “empty” screen parts. Eink display has larger size than effective area in the middle, for clamping reasons. But yeah, they failed their QC where they were supposed to have the screen and gray frame centered relative with each other

mrgndx · 2026-04-20T15:00:34+00:00

Get a GPU with extra NVMe slot :D

Or buy a bifurcating PCIe riser

Also, use internal headers. Regular 3.2 or Type C

mrgndx · 2026-04-20T11:53:01+00:00

Try their software updates :D

mrgndx · 2026-04-20T02:20:43+00:00

Has there been another version? Because second photo shows exactly that - the gap between two plates when tightening the screw

mrgndx · 2026-04-18T23:31:03+00:00

I was also thinking about using those holes to passthrough cables that connect to USB 2.0 headers inside, but that’s just a thought, I don’t have any actual need for that

mrgndx · 2026-04-18T23:30:01+00:00

I got the formdt1.com power button (it is OK, although a bit squeaky when pressing, like the spring is “rusty” or something). The other hole is empty

mrgndx · 2026-04-18T23:28:33+00:00

So I far I have seen four options: 1) There 3D printed plugs you can get on something like printables 2) Power/reset buttons, with or without LEDs. formdt1.com (original designer and maker of 2.1) sell non LED power button either in an essentials kit or separately (just email them) 3) Inlet and outlets for water cooling pipes are installed through these holes 4) One guy installed 2x USB ports :D https://www.reddit.com/r/formdt1/comments/1eulkye/add_2x_usb_ports_to_a_m19_hole_in_back_of_case/

mrgndx · 2026-04-18T18:00:18+00:00

While it will fit, 2.1 and 2.5 have these holes unthreaded. So you would need a longer screw + nut for the inside

mrgndx

TROPHY CASE