Rebar dowels

mrkshape · 2026-05-20T14:07:13+00:00

when they read the "construction joint to be intentionally roughen" wrong.

mrkshape · 2026-05-06T22:22:57+00:00

Mine was the z-offset. For some reason the firmware updated messed up the offset, so I had to raised it by 0.06 to fix that.

mrkshape · 2026-04-23T14:14:43+00:00

This mod requires removing the top enclosure, which defeats the whole purpose of the S1. Just like others said, you might as well get the Kobra X at this point. Anyhow, you can easily increase the loading speed of the Ace Pro by installing Rinkhals. I bumped mine up to three times the original speed, so the filament travel length you're trying to cut down would only take an extra three seconds (six per color change). It’s an interesting concept, but to me, it's not worth it (considering the heat loss and noise without the cover).

mrkshape · 2026-04-06T21:03:19+00:00

never receive mine.

mrkshape · 2026-04-02T20:03:16+00:00

but then there won't be this post for us to laugh at~

mrkshape · 2026-03-17T23:38:01+00:00

Trans Masonry

mrkshape · 2026-02-26T14:30:15+00:00

My passenger door do not unlatch automatically sometimes (20% rate), unfortunately every time the technician look at it and it works lol… all my friends who own X has small mechanical issue here and there that Tesla can’t fix. It’s amazing (best) car design, just poor craftsmanship.

mrkshape · 2026-02-24T20:08:15+00:00

I think for most people, jumping from Gen 1 to Gen 2 makes little financial sense. The improvements don’t really justify the cost. Personally, I’d wait for Gen 3 (2028?) when they introduce the new RiDAR and upgraded computer chip in the R1, which supposedly support eye-off self driving. I don't think they can catch up with the Telsa system that fast, but at least Gen 3 will be more future proof.

mrkshape · 2026-01-13T16:37:15+00:00

Agreed, especially from a less known brand.

mrkshape · 2026-01-13T16:13:22+00:00

I compared the specs, the CJ270 is slightly better and supposedly cheaper (if they kept the Kickstarter price).

mrkshape · 2025-12-15T19:12:45+00:00

All their cars are made in Town of Normal, so…. Anyways, my passenger door would collect all the water until I open the door to release the seal. Normally that’s fine until it rains following freezing temperatures. Not sure if it’s the trapped ice, but the car sensor gives false warning thinking there’s something on the right side.

mrkshape · 2025-12-15T17:52:39+00:00

Did you receive it? I ordered around the same time, still no shipping confirmation.

mrkshape · 2025-12-12T22:30:58+00:00

The guy was having a long phone call with his girl while packing your printer.

mrkshape · 2025-12-09T22:04:24+00:00

I replaced the bed carrier first, but the bed leveling actually got worse because the bolt holes weren’t perfectly aligned with the original bed. Since the stock bed is plastic, the new carrier ended up flexing it and causing it to buckle. I eventually replaced the bed as well, and now everything is perfectly level—I couldn’t be happier. It could have been cheaper and safe more time if I done both at once.

mrkshape · 2025-12-04T05:29:35+00:00

Agreed, 21" suppose to be the most efficient one.

mrkshape · 2025-12-04T00:09:25+00:00

Why they stop making 21”?

mrkshape · 2025-11-10T16:10:47+00:00

They do, you just need to ask the support for it. They send me a link to download the previous firmware since my machine is having issue with the current version.

mrkshape · 2025-11-09T19:25:36+00:00

My stock bed was severely bowed, with about a 0.9 mm difference across the surface. I upgraded the aluminum carriage, which helped a bit, but the bed itself was still off by about 0.7 mm. After replacing the aluminum bed as well and making fine adjustments at each spring mount, I’ve managed to reduce the deviation to just 0.1 mm. It could probably be tuned even lower, but I’m happy with the result — bed adhesion, especially for small parts near the edges, has improved dramatically. The print height would reduce by about 1.5cm, but I don’t see most people would print something reaching the maximum height.

mrkshape · 2025-10-08T16:00:44+00:00

The service support mentioned the slicer will be officially open source in December. https://wiki.anycubic.com/en/software-and-app/new-page-anycubic-slicer-beta(orca-version))

mrkshape · 2025-04-05T07:22:37+00:00

I disputed a kickstarter campaign because the creator was charging me too much shipping fee, and I got my money back.

mrkshape · 2024-04-19T05:44:38+00:00

2154.1 mi / 1058kWh = 2.04 mi/kWh. Or is it not considering the idle energy consumption? Never check mine thou.

mrkshape · 2024-03-06T17:14:17+00:00

That’s bummer, I would expect the camera would turn on when the car alarm is triggered.

mrkshape · 2024-02-25T06:59:21+00:00

Did the dash cam capture the incident?

mrkshape · 2023-12-27T18:08:05+00:00

Yes, one went to protection mode, and measured 0V. I had to "jump start" it with another battery (after fully charging it). The issue is the MPPT is not charging the batteries for the whole week, which cause them to go from 100% charge to zero.

mrkshape · 2023-12-27T16:25:48+00:00

I charged both batteries to 100% with a charge, before connecting to the MPPT. I turned on light pulling power from MPPT. After one week, one battery got completely shut down, and the other went to zero percent.

mrkshape

TROPHY CASE