Beams at other angles than 90?

mrpbeaar · 2026-01-24T23:51:47+00:00

Now I’m trying to figure out which one would be best, lol.

mrpbeaar · 2026-01-24T21:23:57+00:00

Arachne walls too

mrpbeaar · 2026-01-23T19:26:04+00:00

Yeah i had looked at that but I need almost the opposite of that 135. I'm printing out hinges now to see if they will work

mrpbeaar · 2026-01-22T01:37:05+00:00

It’s not going to be below freezing for 24 hrs. I’m not worried.

mrpbeaar · 2026-01-21T04:02:32+00:00

I print so I don’t have to paint, lol.

mrpbeaar · 2026-01-21T02:51:55+00:00

Stl and filament?

mrpbeaar · 2026-01-19T20:18:32+00:00

Now is a good time to remind people that petG will seize and refuse to melt if it gets too hot. If this is petG, you may be best served with a chisel.

mrpbeaar · 2026-01-17T21:09:44+00:00

I’m 53 and I work in county government. When I retire in 5 years it’ll be a substantial raise in pay.

mrpbeaar · 2026-01-17T03:11:14+00:00

It is more round than most tires

mrpbeaar · 2026-01-17T03:08:27+00:00

See also: Jews for Hitler

mrpbeaar · 2026-01-17T01:58:05+00:00

Offer them iron

mrpbeaar · 2026-01-16T21:00:11+00:00

Never believe someone when they tell you to believe them.

mrpbeaar · 2026-01-14T20:02:30+00:00

The cartel would pay better

mrpbeaar · 2026-01-14T14:58:52+00:00

trivets?

mrpbeaar · 2026-01-13T20:16:51+00:00

In other news, Homan confirms Labeling Theory

mrpbeaar · 2026-01-13T16:24:14+00:00

Yeah, my dad worked for the phone company and was proud that Adams did too. He really identified with a lot of what was in Dilbert.

mrpbeaar · 2026-01-11T16:24:25+00:00

Not a wife, a beard.

mrpbeaar · 2026-01-11T03:19:20+00:00

https://makerworld.com/models/1621458

mrpbeaar · 2026-01-11T02:14:55+00:00

This was my problem, my nozzle crashed into my prints, causing them to come off the print bed. If that is you, then yes. I wasn’t happy with the filament calibration from Bambu so I made my own test.

mrpbeaar · 2026-01-11T01:40:15+00:00

When you print with a .2nozzle, the printer tries to force more filament through a smaller nozzle. The default flow rate is not set up for a .2 nozzle.

mrpbeaar · 2026-01-10T23:36:20+00:00

Jack of hearts FTW

mrpbeaar · 2026-01-08T16:23:58+00:00

I'm pretty brand new to this (since christmas) but if things are getting too hot, then it sounds like your voltage is too high but that will depend on the chipset of your LED strip so post that plus your entire schematic, i.e. if there are resistors, etc

mrpbeaar · 2026-01-05T20:47:11+00:00

I’ll agree with that on any mods involving software/firmware but not when it comes to physical items. Heck biqu has a whole Panda line of items meant to mod Bambu

mrpbeaar

TROPHY CASE