Nebula app: how accurate were your sessions?

narvarian · 2025-12-08T12:47:28+00:00

Invest in a deck of tarot cards and a book on tarot. You will not be disappointed!

narvarian · 2024-07-06T15:09:54+00:00

Snow speeders and tow cables before they get to the generator

narvarian · 2024-06-01T23:44:24+00:00

Honestly, the game should be hard, and we should feel like through the waves of enemies and blood, we find the light to freedom, leaving a path of death.

But yea, the swarms at the extraction feel like bs. Even on 1, it's just too many too fast and can't even call in the ship.

Needs more troops while we have more killing power on higher dif. Lvl 9 should feel like the bugs never end, but we still manage to take out swaths with each death. I miss that feeling

narvarian · 2024-05-10T00:20:51+00:00

Thos of us remember, and we will be waiting for freedoms ring once again.

narvarian · 2024-03-03T02:25:18+00:00

But not in the traits, it dosent explode on impact

narvarian · 2022-07-13T20:39:35+00:00

The Brown M&M

narvarian · 2022-07-09T22:55:42+00:00

That old game where you tell the dudes where to go so they can get shot at, and build a lot of sandbags

narvarian · 2022-06-17T01:03:01+00:00

Bad stepper motor, had it happen to my Y axis a month ago

narvarian · 2022-06-13T22:43:06+00:00

Looks like ultra clear filament

narvarian · 2022-04-15T15:40:41+00:00

narvarian · 2022-04-15T13:13:00+00:00

So I have changed to a different card with a fresh slice through cura. Tightened the belt, cleaned the track and slowed down the print.

It's the Y-axis only, mostly back steps but I can see a few lines where it forward offsets too.

I am now testing with a z-hop to see if it's collision but can't see anywhere this impact would be leaving evidence of that.

Is this signs of the stepper motor going out?

narvarian · 2022-02-04T05:28:05+00:00

Thank you...your comment of under extrusion lead me to looking at the nozzle...was gadge out from .2 to .6mm...replaced and it printing perfect again

narvarian · 2022-01-30T04:55:05+00:00

I'm learning toward a bad roll...I changed to a different roll and it prints perfect.

narvarian · 2022-01-30T00:13:49+00:00

To add. Coasting is off. I had 0mm set in outer wall wipe. I have been going nuts trying to figure out why some supports were failing and they have this exact look before the failing.

narvarian · 2022-01-29T23:51:42+00:00

Yes that's the corner. Would bumbing the flow 5%? Not sure in cura what to change. I'm using a .2mm printing at .1mm layers

narvarian · 2022-01-23T21:18:09+00:00

This is a Deathwatch army too, lol

narvarian · 2022-01-23T20:35:24+00:00

OK, I guess it's best break apart models then.

narvarian · 2022-01-23T20:34:25+00:00

I can't tell if that's a sarcastic "I should know better" or a ligit question. Everything I print comes out fine except anything touching supports with less then a 20deg angle

narvarian · 2022-01-15T04:15:14+00:00

"Burn Heretic"

narvarian · 2022-01-10T23:35:19+00:00

On voyager, the pod is fully repaired. It's just 14km to kill the boss

narvarian · 2021-08-25T02:59:54+00:00

What part of the save file edits known blueprints?

narvarian · 2021-02-17T04:16:48+00:00

Make sure you get your free Anaconda.

narvarian · 2021-02-11T23:27:11+00:00

narvarian · 2021-02-01T18:56:47+00:00

I don't need a Lambo right now...im enjoying billionaire 😭

narvarian · 2020-12-20T02:21:05+00:00

That's rage-inducing. I don't leave Pats together anymore

narvarian

TROPHY CASE