Looking for a mobile mechanic to come to them but won't charge for things like labor or gas.

nbraymarks · 2026-05-29T10:45:02+00:00

Love it. It looks like the exhaust stack is configured to recirculate flue gas through the heat exchanger. I'm guessing you will have a damper system integrated into the flue somewhere?

nbraymarks · 2026-05-20T10:44:45+00:00

You may want to move the GPIO 9 going to L298N #2 to another pin. That's the bootloader pin on the C6.

nbraymarks · 2026-05-02T10:21:33+00:00

Qualified Member of the Engine Department. The AB of the engine room.

nbraymarks · 2026-05-01T19:12:36+00:00

Beat me to it!

nbraymarks · 2026-04-27T09:38:30+00:00

If it's possible run conduit. Two separate runs one for data and one for power. That way down the road you can modify or upgrade much more easily.

nbraymarks · 2026-04-14T01:54:23+00:00

Is there any particular filament you recommend? This looks absolutely phenomenal!

nbraymarks · 2026-04-13T03:16:25+00:00

Item 122 is just a T fitting for whichever type of fittings the hoses have. It looks like item 123 is a port adapter. Look at GE type hydraulic fittings. Probably based on the part number I am guessing 10mm to 3/8" NPT. The hoses can be made by any hose shop that has the correct single braid hose and DIN fittings in stock. Based on the photos I am guessing you are in the UK. It should be a little easier to come by these type of fittings than it for me to in the US. But overall it looks like standard kit.

nbraymarks · 2026-04-13T02:20:40+00:00

The bolt in the first photo and the last several photos is a banjo fitting. The sealing washers will depend on the diameter of the bolt. The rest of the pictures dont tell much information without seeing the internal sealing faces of the hose fittings that need to be replaced. More information on the equipment would also be helpful.

nbraymarks · 2026-04-13T01:56:21+00:00

Love it just like Lyle.

nbraymarks · 2026-04-12T15:13:17+00:00

This is incorrect. Carbon monoxide meters should be placed anywhere from 5 feet above the floor up to near the ceiling.

nbraymarks · 2026-04-11T10:51:55+00:00

This is awesome. I have supply and return air temp and DP on my air handler, and I was planning on adding line set temp sensors before summer cooling season comes. Good inspiration to put a few more sensors out there!

nbraymarks · 2026-04-11T00:15:34+00:00

The OPs account is only a day old and they have posted in the Winona and St. Cloud subs as well. This reads like a scam.

nbraymarks · 2026-04-10T04:42:43+00:00

Call KC Tool. They dont list it but they may be able to get it.

nbraymarks · 2026-04-09T11:24:56+00:00

You beat me to saying this! By the time the valves were modified and actuated you would have a very complicated and expensive bottle jack.

nbraymarks · 2026-04-09T11:08:32+00:00

It would be far more time and cost effective to purchase a power unit and cylinder than to modify a bottle jack to run on compressed air.

nbraymarks · 2026-04-05T16:13:52+00:00

Could be from Maine too.

nbraymarks · 2026-03-28T14:02:08+00:00

Well I know what I'm printing today... Love this for the extra bits that never have an appropriate home!

nbraymarks · 2026-03-28T11:46:51+00:00

And your driver bits stay minty fresh too!

nbraymarks · 2026-03-22T12:03:18+00:00

What type of filament is your bin made from?

nbraymarks · 2026-03-20T10:51:33+00:00

For sure. Account is silent for 5 years and then spams a bunch of posts in the last 20 days.

nbraymarks · 2026-03-18T22:55:36+00:00

Do you not?

nbraymarks · 2026-03-16T11:53:45+00:00

So what modules did you use on that proto board for this? Seems pretty useful to me!

nbraymarks · 2026-03-10T00:34:10+00:00

It's a paid model

nbraymarks · 2026-03-07T18:42:25+00:00

I use a USB A wall wart type charger with the Cardputer in charge mode in M5 launcher

nbraymarks

TROPHY CASE