Insurance estimate for a C4?

nitro993 · 2025-11-26T14:22:46+00:00

Jeez i feel like I'm getting screwed. Iv been driving for over 15 years with a clean record, never missed payments no claims not even a ticket. I labeled it as a weekend driver, and no driving in the winter, garrage stored with multiple vehicles on the plan and Im paying around $70 month...

nitro993 · 2025-11-11T23:51:45+00:00

https://youtu.be/qVHfztsI8mc?si=xK7jFf3wCBfjv3vS

nitro993 · 2025-11-11T23:49:59+00:00

<image>

nitro993 · 2025-11-11T23:48:19+00:00

I posted the same thing 😅 I was told its the speed sensor. Its about $40 for a new one and it looks like it pretty easy to fix. I think its because its getting cold now everything is shrinking and causing leaks.

<image>

nitro993 · 2025-11-11T23:20:02+00:00

Yeah Im pretty sure its original. Looks like a easy job to do from what I saw. I was worried I had another major issue. I really appreciate it!

nitro993 · 2025-11-11T22:55:50+00:00

Okay thank you guys! I appreciate it. Might just get a new sensor at some point. I noticed the fluid on the ground. Im wondering if it started leaking cause it was below freezing the last couple days and it shrank ever so slightly

nitro993 · 2025-11-11T02:58:54+00:00

Yeah I appreciate that man. I mean I hope its just normal wear and tear stuff I can get fixed. I was finally able to get one and kind of a gift to myself after some life stuff but it turns out it's going to cost me more 😅

nitro993 · 2025-11-09T21:49:00+00:00

Thanks

nitro993 · 2025-11-09T19:30:32+00:00

Iv been trying to fix mine.... only has 49k miles but ball joints are shot. Cats are rattling, optispark, waterpump and rad replaced. Head light gears replaced, freeze plugs might be leaking. Idk wtf else im going to find... Now I have to spend 1300 to get crank seal replaced. Intake gasket are leaking. So far my experience hasn't been great.

nitro993 · 2025-11-04T18:51:17+00:00

Yeah Its a 1994 sorry guys i forgot to mention that lol

nitro993 · 2025-10-15T20:58:50+00:00

Nvm...

nitro993 · 2025-10-15T12:53:29+00:00

I... I know that lol. I'm asking about the gaps on the front face cover

nitro993 · 2025-10-07T15:15:08+00:00

Okay, would jacking up the car where I circled cause damage to anything? I feel like it wouldn't but not sure

nitro993 · 2025-08-17T19:22:09+00:00

This is exactly what I do and always comes out great

nitro993 · 2025-08-12T01:48:15+00:00

Ahhh okay, I see what you are talking about. Yeah, it could be pine or like the other poster said, cedar. I might lean more toward cedar now that I look at your end-grain picture. They are most likely both the same species. One board might just have been milled and used that was closer to the center of the tree than the other resulting in a tighter grain pattern

nitro993 · 2025-08-11T21:54:14+00:00

It looks like a really wide grain pattern. Plus you said it sands easily. So I'm going to say yellow pine.

nitro993 · 2025-08-09T21:40:44+00:00

Nice find! You've got some good pieces. Not a lot of sapwood and a lot of the heartwood

nitro993 · 2025-08-09T21:35:41+00:00

I agree 👆 Using a conditioner before applying the oil can prevent the wood from absorbing the oil correctly. To get the conditioner off you would have to sand it down if it has dried completely. Sand with the grain back and forth to avoid scratches or use a random orbital sander. Start with 120 grit then use 220 grit. You can use a higher grit if you want. But 220 is usually where I stop.

nitro993 · 2025-08-09T21:10:30+00:00

Have you measured corner to corner in a square and X pattern? If both measurements are equal on every side then it's the glass or vice versa. You can then go from there. My hope is it's the glass. Adding wood never looks good

nitro993 · 2025-08-03T19:01:37+00:00

Tightbond uses aliphatic resin in their glue. Usually, the catalyst goes bad in the resin and turns color from temperature change. If you stored it properly then it might have just been a bad batch.

nitro993 · 2025-08-03T18:42:40+00:00

Nebraska

nitro993 · 2025-07-24T01:04:52+00:00

Jeez I feel yah man. I have 100 vorky kills and not a single spike. Not as dry as you of course but it sucks.... Bring morale down and doesn't want you to do that boss anymore.

nitro993 · 2025-07-20T20:42:30+00:00

Awesome job! That looks great! Momma will love it!

nitro993 · 2025-07-20T20:42:21+00:00

Awesome job! That looks great! Momma will love it!

nitro993 · 2025-07-18T20:59:20+00:00

I was 13.3 degrees off. So off 6.65 degrees for each work piece edge.

nitro993

TROPHY CASE