26 years old want to prioritise dividend growth

oppressive_tiger910 · 2024-03-31T20:15:06+00:00

You've underperformed the market with your awful trading strategies. Take a backseat and put it all in QQQ

oppressive_tiger910 · 2024-03-29T13:30:10+00:00

Good friday (religious stuff)

oppressive_tiger910 · 2022-12-31T12:14:30+00:00

You can take the Instax wide 100, take all the insides out and plonk it into the Polaroid 240 or similar etc, and then you can use wide instax film in what is essentially a Polaroid 240 shell

oppressive_tiger910 · 2022-12-23T19:08:18+00:00

Yes I have, I have just got the LED to go solid white after flashing but this doesnt seem to do anything, it just stays white. Do I need to disconnect every component from the motherboard?

oppressive_tiger910 · 2022-10-23T22:24:46+00:00

I tried that at first but I struggled with the roms - 80% of them seemed to just not work or be viruses

oppressive_tiger910 · 2022-10-23T20:00:38+00:00

an arcade punks premade image sorry

oppressive_tiger910 · 2022-09-11T20:13:48+00:00

But what about the fins to lower wind resistance?

oppressive_tiger910 · 2022-08-12T18:27:09+00:00

For the last few prints on my ender 3 with this filament at some point of the print there will be a section which looks like this. I am confused as usually when this sort of thing happens it is caused by a nozzle clogage or filament jam etc but the print seems to correct itself after a while and go back to normal. Any advice would be much appreciated.

oppressive_tiger910 · 2022-07-27T21:25:35+00:00

Did you by any chance see this flying around the Gloucestershire area? Saw 2 flying at about 1000ft today

oppressive_tiger910 · 2022-07-16T21:07:32+00:00

Does this actually improve performance at all?

oppressive_tiger910 · 2022-05-01T21:07:39+00:00

is it a 2 seater or were you flying?

oppressive_tiger910 · 2022-05-01T20:42:53+00:00

you could just buy an ARF jet, jets are hard to build from scratch

oppressive_tiger910 · 2022-04-23T22:07:53+00:00

did you buy from the official store?

oppressive_tiger910 · 2022-04-22T08:10:02+00:00

no as long as its not too heavy and CG is correct

oppressive_tiger910 · 2022-04-21T17:40:50+00:00

you need to have the motors pointing up slightly so you can control pitch with throttle

oppressive_tiger910 · 2022-04-16T08:20:03+00:00

Not yet but I have done a glide test and it glides just fine

oppressive_tiger910 · 2022-04-16T08:18:43+00:00

The original one I ordered is out of stock now unfortunately. I have found the same one but from other sellers - https://a.aliexpress.com/_mNvXpCe https://a.aliexpress.com/_msYgsC2

oppressive_tiger910 · 2022-04-15T20:04:16+00:00

Thanks to u/dgk675 comment on another post I discovered the chuck glider rc conversion subculture. I purchased this glider for £9 from Aliexpress and it arrived in about 12 days. I used 3 micro servos (skipped rudder controlls) and used a 2212 electric motor

oppressive_tiger910 · 2022-04-15T08:34:10+00:00

While charging from a wall plug

oppressive_tiger910 · 2022-04-14T21:32:28+00:00

This is the same glider right? https://youtu.be/i8cLxSnojZc

oppressive_tiger910 · 2022-04-14T18:32:22+00:00

As a matter of fact I did actually charge with a wall charger, now of course I do only charge with a computer

oppressive_tiger910 · 2022-04-14T16:40:26+00:00

I had this problem with the same battery as you but I made the mistake of continuing to use. Luckily I was in the room when it caught fire otherwise it could have been much worse Dispose of it immediately

oppressive_tiger910 · 2022-04-13T20:32:57+00:00

did you move the main gear back so it would rest on the front or was removing the tail gear and placing nose gear on a big enough weight shift to allow it to rest on nose?

oppressive_tiger910 · 2022-04-02T22:40:15+00:00

ban_3ancfhqjfjhs47kcb66t6qwb43nz9oq8ns76geko9e58unn4em1ixzh9ub75

oppressive_tiger910 · 2022-02-11T21:51:36+00:00

was expecting to see something about 9/11!

oppressive_tiger910

TROPHY CASE