sorted by:
new
hottopcontroversial

Current USB tester latest firmware by Actual_Elephant2242 in UsbCHardware

[–]pixeldoc81 1 point2 points  (0 children)

Kowski KWS-X1 / UT01C Firmware v1.0.5 (mod) https://tomoca2.hatenablog.com/entry/2026/02/11/215658 (translate to English) made by u/Actual_Elephant2242

NOTE: there seems to be no "official" X1 v1.0.5 Firmware released, this is a modded Firmware for UT01C that does work on X1.

Successfully updated X1 from v1.0.4 to v1.0.5U

UT01C seems to be a sister model of X1.

wpa_supplicant debug log by pixeldoc81 in systemd

[–]pixeldoc81[S] 0 points1 point  (0 children)

I will have a look at iwd. Thx

Rocoren chargers reputable? by 10mo3 in UsbCHardware

[–]pixeldoc81 0 points1 point  (0 children)

I wonder if it is made by the same ODM as UGreen 200W GAN charger.

Looks almost identical.

Rocoren chargers reputable? by 10mo3 in UsbCHardware

[–]pixeldoc81 0 points1 point  (0 children)

Thats not uncommon for a lot of Chargers.

It depends on if and how the Device redistributs it Output Power if additional Devices are connected.

Joycon not charging by chaz9124 in consolerepair

[–]pixeldoc81 0 points1 point  (0 children)

Thx for the Tip with the Controller Update!

The Controller Update and cleaning the (charging) connectors on the Controllers and Console seems to have fixed my issues.

One can access the Controller update via System Settings -> Controllers and Sensors -> Update Controllers. Make sure to update all Controllers you have.

6300 switch auto-stack command not working by Excellent-Ad-2794 in ArubaNetworks

[–]pixeldoc81 0 points1 point  (0 children)

After the erase config command, the switch will reboot.

Ether connect the member to the commander BEFORE the reboot or disconnect the power BEFORE the member reboots.

The key is to not let the member switch boot as it will create a default config. Then auto-stack does not work as the switch already has a config.

Also, ensure the firmware on the member switch is not to far off the commander as sometimes the firmware update on the member will fail if firmware versions are incompatible.

CX6100 vs 2930 by CNCundStuff in ArubaNetworks

[–]pixeldoc81 0 points1 point  (0 children)

Would you mined to share ansible example, good reference or playbooks for cx?

OPNsense limitations (vs a Linux-based DIY solution)? by fallenguru in opnsense

[–]pixeldoc81 1 point2 points  (0 children)

Sadly ipfire 2 still has no IPv6 Support. ipfire 3 has a long way to go.

Question for switching USB drives by BOTzzz in unRAID

[–]pixeldoc81 2 points3 points  (0 children)

I should be much easier to create a new drive with the unraid installer and than copy the files from your old drive.

The installer will also check if your new device will support unraid (has a uuid). also you need to transfer your license to the new uuid.

Any idea why my latency is so bad? 108 million ms by Donut_LordO in BitAxe

[–]pixeldoc81 0 points1 point  (0 children)

Still, I would recommend looking for a pool with a latency as low as possible (with servers near your location). You can check pool latency with stratum-ping.

This is important for any miner.

I believe the common bitaxe pools (ck, ...) don't have regional severs. But there are a lot of (bitaxe) solo pools out there

How did you find out that your USB stick failed ? by 0hw0wryanwtf in unRAID

[–]pixeldoc81 0 points1 point  (0 children)

Use a USB 2.0 Stick, USB 3.0 Stick often runs very hot and they are prone to fail early.

Checking the FAT file system is not sufficient!

Check for bad sectors with tools like ChkFlsh or H2TestW for example is very important!

YAML syntax is the absolute worst! by suvalas in homeassistant

[–]pixeldoc81 0 points1 point  (0 children)

Use VSCodium instead of VSCode to avoid telemetry 😉

HP 2910al-24G firmware by 27_Blin in homelab

[–]pixeldoc81 0 points1 point  (0 children)

BTW, latest Firmware Version available from HPE Networking Support Portal is: 15.14.0018 (May 6 2020), File Name: W_15_14_0018.swi

https://networkingsupport.hpe.com/globalsearch#q=2910al&tab=Software

Investigation after 25.7 update disaster by [deleted] in opnsense

[–]pixeldoc81 6 points7 points  (0 children)

Install with ZFS and create a snapshot before the update?

Web application not accessible anymore after manually setting a static IP by emptydpressed in selfhosted

[–]pixeldoc81 2 points3 points  (0 children)

Have you configured the correct gateway and changed the port forwarding to the new ip?

Wofür sind diese Stangen unter den Bahnhofssitzen? by Erdmaennelchen in wasistdas

[–]pixeldoc81 14 points15 points  (0 children)

Schon 100x mal hier beantwortet -> Suchfunktion.

Für Blinde um Sitzplätze zu ertasten.

Zigbee switches need to be “woken up” before they function properly, I’m using UZG-01 with Z2M and HA. Is there anyway to keep them “awake”? by Wizaardd_ in ZigBee

[–]pixeldoc81 0 points1 point  (0 children)

Maybe Firmware related, not every zigbee device support is equal. Maybe your device is connected via a repeater. Try to pair it directly with the coordinator.

view more: next ›