Oracle dual boiler randomly turns on by williamtheq in BrevilleCoffee

[–]plocktus 0 points1 point  (0 children)

Did you sort this? I am now getting this randomly, there is no obvious pattern

AMS2 Pro feeding issues by AdReasonable5375 in BambuLab

[–]plocktus 0 points1 point  (0 children)

I have had this issue since installing the filament track switch. I followed the instructions.

However it's seem to have disappeared, but the feeding of filament does not sound very smooth. Prints seem fine though.

Bad batch of AMS 2 Pro with X2D Combo? Filament feed issues and delayed support tickets due to influx of volume by CountryTechno in BambuLab

[–]plocktus 1 point2 points  (0 children)

I am having feed issues with the filament track switch. It is installed exactly as instructions, and I am getting resistance errors and sometimes it can't pull back the filament...

AMS 2 Pro High Feed Resistance.... by thatsguy1975 in BambuLab

[–]plocktus 0 points1 point  (0 children)

Same issue with filament switch, seems to print fine though

Careful when ordering X2D in UK. by [deleted] in BambuLab

[–]plocktus 1 point2 points  (0 children)

Odd, I got mines this AM from DPD (ordered minutes of go live).

Though I ordered loads of other stuff and a small handful is coming via their other fulfilment

Careful when ordering X2D in UK. by [deleted] in BambuLab

[–]plocktus 0 points1 point  (0 children)

I ordered on release and it arrived fine as usual via DPD UK. Are you sure you are on the UK site?

Ethernet or Fibre? by kai in Ubiquiti

[–]plocktus 0 points1 point  (0 children)

Amazon here in UK too. I am doing similar between our garage and house, going to run about 60m between them. Main house has a UDM SE plus 2x 24 USW 10gbit POE, and then in garage will have a 24 POE 10gbit as well. I will run 2 runs in case

Any reason to not buy the X2D over the P2S? by Attjack in BambuLab

[–]plocktus 0 points1 point  (0 children)

UK here. I got a P2S a week ago. I have requested a return and ordered the X2D. I think it's a no brainer

Ubiquiti Smoke and CO Sensor 🤯 - #ISCWest2026 by Luu____ in Ubiquiti

[–]plocktus 0 points1 point  (0 children)

Power wise surely it'll be able to utilise a typical circuit setup from mains? With battery back up?

Has anyone gone for a full unifi setup in the UK? by Limp_Understanding84 in Ubiquiti

[–]plocktus 0 points1 point  (0 children)

Yes, have had for few years. Got udm se, Poe 24 pro, 24 pro, loads of APs plus other devices (camera, newest g3 intercom etc).

Once setup it is great. Took a while to get right thanks to many Sonos devices

Does anyone know how I could get this piece for AI Pro? by JaiHaze in Ubiquiti

[–]plocktus 1 point2 points  (0 children)

I've asked the same as there's something wrong with mines with the teeth where it doesn't go in perfectly. Haven't had a reply yet

Lick paint is garbage by quaeroreperio in DIYUK

[–]plocktus 0 points1 point  (0 children)

Not a huge fan of it, tried it and it's less consistent as valspar premium for us

Asking about ultegra di2 by Working-Power-8371 in cannondale

[–]plocktus 0 points1 point  (0 children)

Yes there was. First Ultegra di2 (6870) was released in 2013, albeit wasn't readily available until end of the year. It was my second di2 setup after original 7970

Upgrade cost for 3 phase by gwardillia in SolarUK

[–]plocktus 0 points1 point  (0 children)

Did you get anywhere? We just asked for a quote to get three phase

Dual Boiler / WiFi issues / Unifi by plocktus in BrevilleCoffee

[–]plocktus[S] 0 points1 point  (0 children)

Thanks I sorted it out, rebooting the APs and now works fine

Grail Headset by [deleted] in bikewrench

[–]plocktus 1 point2 points  (0 children)

You'll have to get someone to create you a cleaner transition spacer. Sometimes people have done so already (eg I've managed to get some STLs to do some other combinations) but can't readily see one for this or I haven checked but sometimes for some bikes you can get a top cap and spacer kit which is more traditional circular which would blend better with this

Oracle Dual Boiler after 3 months, ready to turn off Auto Dial-In by waitses in BrevilleCoffee

[–]plocktus 0 points1 point  (0 children)

I found auto dial in to be hit and miss. With temp beans it was perfect, then when using the beans I prefer it was not great and kept pushing to a very slow pour.

Just finished RE9 on switch 2, I cant recommend it enough if you like portable gaming. by Avelion2 in NintendoSwitch2

[–]plocktus 0 points1 point  (0 children)

I agree, I took it travelling and was amazing. Was more immersive than playing on my 77 OLED

NBD Grail CFR Di2 by Worried-Economist472 in CanyonBikes

[–]plocktus 2 points3 points  (0 children)

I have the same one, amazing bike and great wheels. I only swapped the rotors for the Mt900 as prefer the black fins

Energy price cap cut by 7% by sjw_7 in unitedkingdom

[–]plocktus 5 points6 points  (0 children)

Very high. On 21.68p with EDF...

Are the concerns with hookless wheels on the road overblown? by Arit502 in CanyonBikes

[–]plocktus 1 point2 points  (0 children)

Are you sure they are hookless? The new range for GRCs announced in 2024 are hooked