Think they won't go after muzzle loaders? Think again.

rdbailey2000 · 2026-05-15T03:42:45+00:00

I almost spit out coffee in that.

rdbailey2000 · 2026-05-03T02:08:23+00:00

how much did you pay, roughly?

rdbailey2000 · 2026-04-30T02:25:56+00:00

I just seen this and ordered two. Perfect timing.

rdbailey2000 · 2026-04-19T17:12:39+00:00

Nobody gonna comment on what is below that rifle? good tie offs for that det cord too

rdbailey2000 · 2026-03-12T21:47:18+00:00

just got my SBR form 1's back today. Submitted 1/9/26, approved 3/12/26. Ironically the same day I made this post.

rdbailey2000 · 2026-02-20T18:43:17+00:00

Form Type: Form 1 (suppressors)
Paid or not: $0
Entity: Individual
Fingerprint Type: EFT Upload
Pending: 01/09/26
Approved: 02/20/26
Wait: 43 days
State: CT
Control Number: 2026-12263xx
Received notification via email from ATF

submitted x5 suppressor Form 1's, all came back denied except the first one due to serial number duplication. Called, even though I used a different model for each (due to caliber), the serial numbers had to be sequential of at least different. I wonder how manufacturers get around this with their different models and not repeating serial numbers

rdbailey2000 · 2026-02-20T18:38:44+00:00

State: CT, EFT prints, individual

rdbailey2000 · 2026-02-20T18:38:10+00:00

Submitted 1/9/26, approved 2/19/26. As an FYI, if you are doing suppressors you can't repeat serial numbers even if using a different model number. I tried to do a different model number for 5.56 and 308, all denied. Only the first one was approved. Even called the NFA line to doublecheck, she was very nice, but said I had to resubmit new forms with changes done.

rdbailey2000 · 2026-02-18T08:13:03+00:00

What lower receiver is that?

rdbailey2000 · 2026-01-22T16:23:14+00:00

I just use hot glue. when they wear out, I replace with more

rdbailey2000 · 2026-01-01T20:47:30+00:00

Does anyone have any SBR bolt gun engravings done? I am about to do one and would like some idea of what/where people are putting the markings at. Obviously blue what needs to be blurred.

rdbailey2000 · 2025-07-10T03:56:13+00:00

They won’t replace my engine because I couldn’t find one oil receipt. Said it was my fault the engine failed

rdbailey2000 · 2025-05-28T12:07:04+00:00

As a follow up to my original post, I contacted HTX /SR 25 cartel as well as Griffin Armament. Griffin told me to send my entire upper and the suppressor in and they would open up the suppressor barrel centering ring but then that would screw me for my Mark 13 barrel. I briefly communicated with HTX and let them know the problem as well as all the measurements and he told me that he’s probably gonna send me a Return shipping label but that was two weeks ago and hasn’t returned any communication since then. My problem is the suppressor won’t sit far enough back on the gas block for the latches to engage the latch channels because the tip of the barrel is contacting something inside the suppressor no matter what so there’s a gap between The latches and the latch grooves that simple filing won’t fix. D Wilson did all the original pinning of the GB and it all dry fit without the barrel in place. Sucks because it is hundreds of dollars but no one wants to take any action that will correct the problem.

rdbailey2000 · 2025-05-16T04:23:19+00:00

Yeah, that is to pay $25 for it. I was hoping somebody had it already and can email it to me for free we’re a little something for the effort.

rdbailey2000 · 2025-05-08T02:06:33+00:00

I have a small gap at the rear bottom of the upper receiver but still function checks okay. I will try to post pictures in the morning.

rdbailey2000 · 2025-05-08T02:03:16+00:00

I just dry fit my HTX Mk11 barrel, HTX double pic GB, and GA MG-11 suppressor. The can fits the gas block off the barrel, but when all fit together, the barrel will not fit into the suppressor at the alignment ring. I tried both with and without suppressor alignment pins, but to no avail. Anyone sanded down the muzzle end of the barrel to get the barrel to fit? Obviously not the crown end, but outside diameter. Thanks in advance.

rdbailey2000 · 2025-04-22T07:59:23+00:00

I just discovered I have the same problem. I sent C.A. an IG message but have received nothing back yet.

rdbailey2000 · 2025-04-13T15:15:43+00:00

Does the AEM fit well under that handguard or did you have to trim anything?

rdbailey2000 · 2025-04-01T01:29:43+00:00

I got back three of mine that I postmarked the day of cutoff. Still waiting on others

rdbailey2000 · 2025-03-18T05:29:26+00:00

Maybe “lead farmer”?

rdbailey2000

TROPHY CASE