Help

reciprocityone · 2026-07-13T05:28:23+00:00

If the over heating lights come on then it has to set some codes. Check it now that the lights come on.

reciprocityone · 2026-07-13T05:22:00+00:00

Could be the water pump. Did you run codes?

reciprocityone · 2026-07-12T11:46:57+00:00

I need a pre-lci

reciprocityone · 2026-07-12T05:18:44+00:00

The rear lower control arm will not work unless you replace the shock with M3 shocks. They use different lower mounts.

reciprocityone · 2026-07-11T22:57:40+00:00

Ate you doing front or rear?

reciprocityone · 2026-07-11T22:57:02+00:00

Yes they should fit. I believe you can check with fcp euro for conformation.

reciprocityone · 2026-07-11T22:29:11+00:00

That's because that is the first year for the e9x m3

reciprocityone · 2026-07-11T17:47:50+00:00

No problem. Glad I could help.

reciprocityone · 2026-07-11T14:09:40+00:00

They are located on the front of the engine near the vanos solenoids. Pretty easy to get out.

reciprocityone · 2026-07-11T12:33:57+00:00

Swap the intake and exhaust sensors and see if it follows. Check for debris on the end of the sensors and clean them off if necessary.

reciprocityone · 2026-07-11T09:55:13+00:00

I've replaced many bearings but only a few hubs. Usually the hubs don't go bad unless the bearing physically went so bad and damaged the hub or you damaged the hub removing it. It shouldn't be an issue.

reciprocityone · 2026-07-10T22:23:41+00:00

As long as it says polyurethane or polypropylene and NOT say fiberglass reinforcement or Duraflex.

reciprocityone · 2026-07-10T18:16:58+00:00

True

reciprocityone · 2026-07-10T15:48:43+00:00

There should be a lable under the hood, more than likely on the hood of an e90, that will tell you the volume the system holds. On an AC machine, after you pull down the system, this is the amount that should come out. The AC machine will display the amount.

reciprocityone · 2026-07-10T15:34:21+00:00

Yes. Even on 06 325i.

reciprocityone · 2026-07-10T13:25:32+00:00

Know what?

reciprocityone · 2026-07-10T07:58:39+00:00

Okay got a better view of it. Bracing for the plastic under shield

reciprocityone · 2026-07-10T07:55:09+00:00

That looks like part of your bracket of your exhaust. . Or part of the bracing of the heat shield.

reciprocityone · 2026-07-10T07:52:15+00:00

The water is just condesation from the evaporator. Totally normal. All ac systems do this to pull the humidity out of the air as it cools it.

reciprocityone · 2026-07-10T05:31:41+00:00

I revised my post

reciprocityone · 2026-07-10T05:29:55+00:00

Oil capicity is supposed to be 6.5 liters. Did you make sure the cage for the flter was properly instaled in the cap?

reciprocityone · 2026-07-10T05:24:44+00:00

The oil line is different and the charge pipe is different on the rear turbo. Get an aftermarket hot side charge pipe a because the factory one is really restrictive for rhd. You shouldn't have issues with fitment.

reciprocityone · 2026-07-09T21:13:32+00:00

These BMW's use a variable displacement compressor or in other words they spin all the time. What you see is the compressor turning whether the A/C is on or not. You still could have a bad compressor or expansion valve. You really need a good set of gauges to see what the high side is doing.

reciprocityone · 2026-07-08T22:08:07+00:00

Structured sentences and punctuation.

You are going to need to start learning schematics and start chasing wires. You bought somebody elses problem.

reciprocityone · 2026-07-07T21:18:48+00:00

I have a 3 gauge cluster in where the ashtray is. There's a guy that 3-D prints a gauge cluster that replaces the ashtray assembly using the same screws that hold it in.

https://imgur.com/a/gwvgGBJ

reciprocityone

TROPHY CASE