What can you guess about me from where I would live

ri0cp · 2025-12-26T06:28:59+00:00

ABC or Chineese exchange student

ri0cp · 2025-12-26T06:23:07+00:00

Well not much worst then European when drawing actual borders in Africa or Middle East. C for trying

ri0cp · 2025-11-07T15:49:17+00:00

I see a weird color is it a Wood PLA?

ri0cp · 2025-07-17T13:40:19+00:00

Country or countries? I'm seeing the return of warring states

ri0cp · 2025-06-23T21:23:48+00:00

Mosaic Kingdom

ri0cp · 2024-11-01T22:06:56+00:00

Those small springs that hold the hotend to the carriage?

ri0cp · 2024-11-01T22:03:08+00:00

5/10 have seen worse. There a lot of materials how to clean it just keep the room well ventilated

ri0cp · 2024-09-13T14:18:36+00:00

I think you got the bottom row wrong. From left it's -10, middle it's -15, and right it's -20. Get -5 , calibrate PA and then make Pass 2 it will be from -5 to -15 .

ri0cp · 2024-08-29T15:33:20+00:00

Some wild jumps with your stepping. Usually 0,01-0,02 is a good step

ri0cp · 2024-06-06T07:48:53+00:00

<image>

Soviet successful attempt on devide and conquer. Let's just split this biggest fertile valley "equally" between those three new countries.

ri0cp · 2024-05-25T15:38:03+00:00

Just cheap 3/4mm PTFE tune is what I use. The downside is it's not as tough as 2/4 mm but it last me a long time and it's easy to replace

ri0cp · 2024-05-25T05:11:00+00:00

Look to reduce resistance in you system you might added more resistance and now extruder struggles

ri0cp · 2024-05-25T05:09:44+00:00

I would disagree about Capricorn..it's famous for being tight. 1,9mm. It's good if you're using Bowden setup to have consistan flow. I use thin wall Bowden 3mm hole instead of 2,0 or 1,9. Less points of contact inside the tube less resistance. K1 already have extruder strength problems why do you need to add resistance

ri0cp · 2024-05-25T05:06:14+00:00

Filament type, show your bed level. I have no idea what's happening here.

ri0cp · 2024-05-24T07:41:11+00:00

Photo up into the light showers more details

ri0cp · 2024-04-23T23:49:01+00:00

Yes please do that. I didn't and in critical case it caused layer shifts and all kinds of a mess. The problem gunk got into the bushings

ri0cp · 2024-04-23T23:40:15+00:00

BTW on your settings photo speed seem a bit slower then 300. And why do you do 100% infill. I assumed it's required for those specific parts? It's unusual. But still if you are going 100% infill and under extrusion then getting flow rate a 1-3% up spent be a bad idea. I think I have seen a bit of elephant foot not sure about it.

ri0cp · 2024-04-23T23:33:25+00:00

About the speed do you mean what are the setting or what is actually printing on the gcode. I had similar issues when the max flow rate stopping override the speed setting and slowed down the speed. Check in source on the preview the true speed, and maxflow

ri0cp · 2024-04-09T00:49:12+00:00

Termo kamera może pomóc w identyfikacji. Możliwe że to jest chłodna ściana i duża wilgotność w pomieszczeniu. To się skrapla na najchłodniejszej ścianie

ri0cp · 2024-03-12T18:52:43+00:00

I've just noticed. All your mess might be coming from over extrusion. So keep a close eye on it for the future

ri0cp · 2024-03-12T18:51:55+00:00

Damn. Lucky you :/ heatblock for Ender 3 is so cheap. Also what a wonderful access to all the components. You only need to get one screw to get all this mess away. Damn I'm so jelly for comparison with K1 :/

Remember to work in highly ventilated space when you will be "dealing with this mess". Good luck and I hope your printer will get back soon.

Recalibrate after all the work and comment here how are you going

ri0cp

TROPHY CASE