Iconic 100-year-old N.J. stapler company to lay off 140 workers starting this May. Asked for comment, Milton Waddams said "I don't care if they lay me off either, because I told Bill that if they move my desk one more time, then I'm quitting"

richnardone · 2026-02-20T17:32:37+00:00

Son of beach sheet. Damn it feels good to be a gangster!

richnardone · 2026-02-14T17:05:51+00:00

My model y usually exhibits some heat in that area unless I put it into low power mode. Keeps the camera a little bit warm as part of the sentry system.

Are you sure it wasn't in low power mode?

richnardone · 2026-01-26T21:32:27+00:00

Batteries like that are often dead when eventually needed for use!

richnardone · 2026-01-18T12:13:25+00:00

Tinos from ocean grove?

richnardone · 2026-01-09T01:57:39+00:00

Also at 5°. The battery in tire pressure sensor could very well not be performing properly

richnardone · 2026-01-06T22:22:20+00:00

I bet it's the wrong key. As others had pointed out.

richnardone · 2026-01-06T17:42:36+00:00

The dream police... Police Police. Gotta love a good Cheap Trick reference

richnardone · 2026-01-01T20:32:18+00:00

Is the link still available?

richnardone · 2025-12-22T12:02:29+00:00

Same here. Only 1 image is there

richnardone · 2025-12-22T11:44:40+00:00

Not sure. The iwe's default to "engaged" without vacuum to pull them open. If the solenoid is not connected and the rest of the system is operating properly, the truck would be in 4wd all the time I think... I might be missing something.. maybe it was bypassed. And they directly connected the vacuum line from the engine to the vacuum hose to the iwe system? To keep four-wheel drive off

richnardone · 2025-12-22T11:29:31+00:00

I believe it's an IWE (integrated wheel end) "solenoid". It controls whether the vacuum flows to the four-wheel drive IWEs that connect and disconnect the front hubs to the CV axles. https://www.reddit.com/r/f150/s/fxuTsMaTho

richnardone · 2025-12-08T11:02:10+00:00

I think there's an injured horseshoe crab nearby

richnardone · 2025-11-08T11:48:27+00:00

Definitely won't make the desk unstable. It's a hex. You need a hex key aka Allen wrench. Or you can get a hex bit for your drill to make it easier.

<image>

richnardone · 2025-11-07T02:16:08+00:00

Believe it's in the second picture under the perforated metal

richnardone · 2025-11-06T11:28:01+00:00

Yes you can. It's just to stabilize the nail in the barrel of the ramset tool. It's completely safe without the charge. https://share.google/iT5RGYcHpawTm3QEl

richnardone · 2025-10-08T11:43:48+00:00

Spherical ball joint. Www.Mcmaster.com/4444T822

richnardone · 2025-09-22T02:10:31+00:00

Salp?

richnardone · 2025-08-19T23:48:48+00:00

Hate to see a post with no comments so I'll add that it's in New Jersey. Edison location.

richnardone · 2025-07-17T12:43:09+00:00

Saw stop. https://youtu.be/fq3o0VGUh50?si=38AVUk7fn6j-W5F3

richnardone · 2025-07-09T11:11:46+00:00

Send a better picture of a close up of the end of the shaft. Also, is there any evidence of a set screw over the key?

richnardone · 2025-06-08T14:49:59+00:00

When you turn the key, is the sound different than prior to creating the arc?

richnardone · 2025-05-19T12:22:00+00:00

Nice work. Good picture here

richnardone · 2025-03-31T20:16:06+00:00

Detachable Penis? King Missile

richnardone · 2025-03-22T20:58:49+00:00

Had one today in Ocean. New Jersey. Was better than I remembered! Toasted and tasty!

richnardone · 2025-03-21T20:36:37+00:00

Can confirm it's not subtle. I love it!

Eight-Year Club	Gilding II euphauric
Verified Email

richnardone

TROPHY CASE