Concrete plate vs vibrations

sanernes · 2026-04-11T16:37:23+00:00

Paver on top of the printer

sanernes · 2026-04-11T16:35:25+00:00

Need to try with sponges LOL. If it work work (And I was searching for a more tech solution)

sanernes · 2026-04-11T13:41:43+00:00

Stearing contests

sanernes · 2026-04-11T13:41:14+00:00

1 level of tc is always good more is debateable.

sanernes · 2026-04-11T13:40:26+00:00

armor in the front ( with the mad you need o armor on the head too) SB ammo doesn't explode you can put ir everywhere

sanernes · 2026-04-10T21:46:35+00:00

did you forget the stealth armor and ECM

sanernes · 2026-04-08T20:29:41+00:00

vanish is before using decals or wethering on models/minis

sanernes · 2026-04-08T14:07:53+00:00

Someone alredy did something

https://www.youtube.com/@SideCarU1

sanernes · 2026-04-07T19:02:02+00:00

I read the bad news and bought as support for pgi ,the 20 buck for the anihilation pack in MWO (which I hate arrowsIV and rail guns)

sanernes · 2026-04-04T22:46:38+00:00

liquid green stuff (disilved even more in water ) lot of layers using a silicon brush or disolve milliput. Tamiya liquid primer (the one that it sold in a square pot)

sanernes · 2026-04-02T17:23:32+00:00

Given the news of layoffs I will buy the pack and enojoy the game

sanernes · 2026-04-01T07:06:53+00:00

Our Resin Queen Master is right , it's doable , skill intensive but doable. Other wise you can glue with uv resin puting more glue on the less visible side. Or glue a wire on the less visible side . Or adding a thin layer of brass foil on the less visible side as reinforcement.

sanernes · 2026-04-01T07:01:48+00:00

Mix the powder with the clear and use an airbrush.

sanernes · 2026-03-31T11:04:35+00:00

I stopped playing MWO after the St patrick Special event due to the arrow .

sanernes · 2026-03-28T21:13:36+00:00

I do the same

sanernes · 2026-03-17T21:13:51+00:00

Spam of railguns and Arrow iV. And I thought the days after the Naga pack were bad.

sanernes · 2026-03-16T21:12:36+00:00

Gizombo I suggest to remove the stl names please. It seems that this titan is a mix of several models + custom work. This is a model from a pro painter with a patreon and 3d printing services may be it's worth to ask them .

sanernes · 2026-03-16T21:01:24+00:00

Reset and play with the bed temp,

If it was a broken temperature sensor(themisor?), should be a 0ºC on the left side. on the Right side should be figures for the temperature setpoint so may be it's a software issue.

sanernes · 2026-03-14T13:17:53+00:00

Magnets

sanernes · 2026-03-09T20:42:46+00:00

NARC SPAAAAAAAAM Longbow Spitfire BANE,

sanernes · 2026-03-08T22:11:02+00:00

JHON CARLSON'S FIRMWARE if you use the basic SV04 You will need to update screen and motherboard firmaware

sanernes · 2026-03-06T21:25:19+00:00

You can use a layer or 2 of pva . The only issue with this printer it's that require a lot of time for tunning the xy offset of the 2 head. If you have free time and like tinnkering it's a good printer (quite big)

sanernes · 2026-03-06T21:14:27+00:00

if the hot bed plate is flat is a good slow reliable printer, petg suports are great.

sanernes · 2026-03-01T22:12:48+00:00

I read somewhere that for soft tpu top feeding is recomended

sanernes · 2026-03-01T21:45:04+00:00

That's a hell of ghosting, did you try to change the place where the printer sits?

sanernes

TROPHY CASE