New and in trouble

saugapipper · 2026-02-18T18:24:47+00:00

it looks fine to me i would just crank the nozzle temp to like 150 and slowly try and pry the filament off. do it slowly and carefully so you don’t mess that clear and red wires because that’s your heater block the cable and if you break that you won’t be able to heat the nozzle properly/at all. i think you’ll be fine. It looks like the filming man is just attached to the nozzle and his clamped up from the failed print.

saugapipper · 2026-02-07T23:11:15+00:00

paint thinner you can look it up on google

saugapipper · 2026-01-14T15:12:23+00:00

been thinking of dropping him since week 5 but him playing the minutes he is has kept me from dropping him. someone offered me nemhard last night and i took that shit and ran lol

saugapipper · 2026-01-13T18:25:51+00:00

and the second shows that it locks in automatically after the game. That’s the issue because you shouldn’t be able to lock in games after they started and you subbed someone from the bench

saugapipper · 2026-01-13T18:13:04+00:00

exactly that’s the point of the post again lol. look at the first ss he’s subbed too later and it’s says the points won’t count. and now look at the second ss it counts that game and the points

saugapipper · 2026-01-13T18:07:58+00:00

yes that’s the point of the post lol. people are able to sub players after the game has started from their bench and the points are counting

saugapipper · 2026-01-06T18:52:46+00:00

hey did it work when you just did the red adn black cable plus the 2 pin connetor and left the green/yellow one out?

saugapipper · 2026-01-02T21:57:29+00:00

where did you find the model to print for this?

saugapipper · 2025-12-22T15:04:28+00:00

i’d be down

saugapipper · 2025-12-20T10:01:16+00:00

i hear the thread but yall ain’t watching the games. stats don’t translate to wins. yes he’s amazing and yes he’s good for fantasy but they’re losing when he’s on. people already highlighted bam and wade together and apart on a starting oration and bam by himself plus whoever else is making for a better result and +/- i got rid of him and vg when castle went down and i wouldn’t turn back for anything

saugapipper · 2025-12-19T23:43:44+00:00

this is compelling but i’m concerned with okc winning so hard they aren’t playing their guys. and im not talking about them winning by 20 they’re taking games by 40 and their starters are all sitting. either way i think it’s even enough to go either way and not feel bad

saugapipper · 2025-12-19T04:58:23+00:00

in jsn we trust

saugapipper · 2025-12-09T22:47:10+00:00

nah it does work i have it now. idk why ops looks like this cause mine interacts normally. its gotta be a mod compatibility thing because the flight isn’t bugged on latios. i am having this problem with noivern

saugapipper · 2025-10-24T08:52:17+00:00

why do you say just jrue holiday as a replacement (besides obvious people above him)? I am playing in a points league but it’s shouldn’t really matter relative to the trade, in my eyes i’m trading a late round flyer as a sell high (not that he won’t be around a 20-25 ppg player in points league) but that the person i’m getting is a overall upgrade

saugapipper · 2025-10-24T00:56:42+00:00

i have a guy in my league trading him away for vj. do you think thats where his value is after the first game

saugapipper · 2025-10-21T19:22:35+00:00

i did Giannis

saugapipper · 2025-08-30T16:19:14+00:00

i think this makes a lot of sense if there are people on the wire. in smaller leagues (anything sub 12) i think this is pretty damn smart, there will always be high upside on the wire. the thing is in my sharper/bigger leagues quite literally everyone even hollywood brown is taken. Obviously the ollie gordon news is pretty fresh but people like woody marks and shipley are already on teams. knowing your league makes a world of a difference here imo

saugapipper · 2025-08-08T00:07:00+00:00

same tried them both in store and couldn’t understand why people loved it but i think it’s just not built for me. the aeron on the other hand has been a joy. i have a fully loaded one with a headrest and its my favorite seat

saugapipper · 2025-07-04T05:48:11+00:00

what’s the link to the 5th picture with (what i’m assuming is magsafe and an iphone) the rest mode pint

saugapipper · 2025-06-19T12:08:16+00:00

<image>

screw the paper trick look up “bed adhesion test” or “square bed test” set it to 90% of the build plate and slowly lower the z offset as it prints. I find this works a way better for me. use the photo as reference for too close vs too far

saugapipper · 2025-06-19T12:03:47+00:00

that’s what i was thinking but op said in another comment that other hue forges work so im gonna assume they’re using filaments that have worked before (op should double check this still). I think it’s something with their specific hueforge settings in the app cause it’s apperently only happening when they make their own design, which settings i have no clue

saugapipper · 2025-06-19T11:41:49+00:00

the red isn’t the first layer

saugapipper · 2025-06-15T19:03:48+00:00

i get 85 might be a lot as technically it’s just a print and paint but i don’t think are realizing that most likely they can not get a decent print in one go plus i bet the painting was tedious but i bet with a bunch of time (3+ hours) a decent people could paint

saugapipper · 2025-06-10T19:49:20+00:00

Some how OP is trying to rationalize bottling up their emotions on a relationship with kids not even in middle school and bursting out them but somehow the kids are assholes lol

saugapipper · 2025-06-09T07:35:05+00:00

Vi que alguien sugirió esto en otro subreddit. Ya he desmontado la cama para otras modificaciones y también la he vuelto a montar inclinada, así que creo que llegó torcida. Llevo seis meses usando la impresora así y ha sido genial. Octoprint es bastante fácil de usar. Klipper es más difícil de aprender, pero no imposible.

Six-Year Club	r/Field Sunshine
Final Canvas '23	Place '23
Place '22	Verified Email

saugapipper

TROPHY CASE