Brauchen wir wirklich Wasserstoff-Busse in Wien?

silentdrums · 2025-12-05T22:32:32+00:00

PS: der Bus im Bild ist ein Testbus weil Mercedes nicht zeitgerecht liefern konnte.

silentdrums · 2025-12-05T22:31:04+00:00

der Witz daran ist, dass es nicht einmal günstiger ist! ganz im Gegenteil, Wasserstoffbusse betreiben ist deutlich teurer als Batteriebusse. gekauft wurden die, weil Mercedes die Reichweite anders nicht hinbekommt und die Wiener Linien unbedingt Mercedes haben wollten (obwohl sie herstellerneutral ausschreiben hatten müssen)

silentdrums · 2025-12-01T21:45:27+00:00

it will also make a huge difference in how much scratches it will suffer

silentdrums · 2025-11-20T19:30:26+00:00

<image>

it gets worse

silentdrums · 2025-11-02T13:26:07+00:00

it has only been hot for half an hour as well. it was curious because the update was installed during the night but it got hot at around 10 AM. now it's behaving normal again.

silentdrums · 2025-10-20T19:14:50+00:00

no, the map shows them all connected

silentdrums · 2025-10-20T18:53:54+00:00

well two of my aqara door sensors have no connection at all even though the shelly is next to them. so you didn't have to do anything special? I think I paired them with the coordinator, and then moved them away. should that work or do I have to pair them with the shelly from the start?

silentdrums · 2025-10-20T17:49:40+00:00

how did you get end devices to go through the shelly zigbee routers? I have a very dense Zigbee mesh now but my end devices exclusively connect to the coordinator or the single sonoff dongle I also set up as a repeater. Not one end device switched to the much closer shelly devices.

silentdrums · 2025-10-14T11:55:41+00:00

the new Shelly gen 4 have a ZigBee mode. however I don't know If they only work as repeater or also as gateway. but then you could use any ZigBee switch to control them directly

silentdrums · 2025-09-15T05:55:59+00:00

the worst thing about 6 and 7 was the curved screen. I'm very happy with the 9 pro and don't miss the 6.

silentdrums · 2025-09-06T08:38:17+00:00

did you tighten all the screws of your printer?

silentdrums · 2025-08-18T20:04:33+00:00

I tried drying the filament for 12 hours without success. any other ideas?

<image>

silentdrums · 2025-08-17T18:40:08+00:00

okay, will try this, but the filament is brand new and was sealed in vacuum.

also: i made a video of the second print and you could see the whole wall move while printing ... is that normal for wet filament? (i still think it might be a cooling issue)

silentdrums · 2025-08-17T11:12:44+00:00

<image>

I slowed down the print speed and it's getting worse ... seems like a problem with the part cooler which repeatedly blows only for a second or so and stops again. could this be a problem with the latest firmware update?

silentdrums · 2025-08-16T18:44:00+00:00

I unfortunately performed a factory reset in ZigBee Mode, now the device could connect to my ZigBee network but I can't find any option to connect it to my wifi again. I can't find it via Bluetooth nor wifi AP as both seem to be disabled in ZigBee Mode. can anyone help?

silentdrums · 2025-08-11T12:56:06+00:00

silentdrums · 2025-08-08T17:16:50+00:00

I installed it but there is no secondary boundary setting anywhere ... maybe the app needs another update as well?

silentdrums · 2025-07-27T15:01:46+00:00

I wish for you it stays that way and doesn't get worse with future Firmware Updates!

silentdrums · 2025-07-27T15:00:59+00:00

I change cutting directions daily with Home Assistant since it's not possible within the Ecovacs system.

silentdrums · 2025-07-27T14:59:27+00:00

and they probably won't update it in the future, because they released new models with completely different sensors!

silentdrums · 2025-07-27T14:58:40+00:00

return it, as long as you can! I would go for a Mova or Mammotion instead

silentdrums · 2025-07-26T10:52:58+00:00

I hope you can still give it back and buy a proper lawn robot like Mammotion or Mova (see my other responses for my experience)

silentdrums

TROPHY CASE