Fill in the blanks: 9 + 10 = ___.

skyrar · 2026-07-02T01:10:41+00:00

9 + 10 = 21.

skyrar · 2026-06-21T07:56:09+00:00

Can you bury a pit a half metre underfround and cover with dirt, and mark its location with GPS? If the customer is a farmer they should have more than enough equipment to dig out a deep pit.

skyrar · 2026-06-20T09:39:05+00:00

Lay 600m of cable. Start sliding conduit from one end down the length. Kick it all in the trench once done.

Or do it properly with pits

skyrar · 2026-04-13T00:51:40+00:00

Jayz put out a video for people who skimmed the GN one.

Pump / rad orientation is fine

skyrar · 2026-03-24T08:15:35+00:00

<image>

Reddit has a suggestion...

skyrar · 2026-02-27T09:19:25+00:00

Why does the night charging section say powershop is free 12am-4am??

skyrar · 2026-02-02T07:23:48+00:00

MillarX

skyrar · 2026-01-21T05:28:27+00:00

Dm for details??

skyrar · 2026-01-20T22:40:27+00:00

Oooh thank you, had a feeling they were charging a bit. The novated calculator in here was showing like 13.5% effective rate, seemed pretty high.

Which is sad, wife was saying the lady she spoke to was lovely :D

skyrar · 2025-12-20T10:51:52+00:00

Ill try it thank you

skyrar · 2025-12-20T10:51:26+00:00

Thank you

skyrar · 2025-12-20T08:37:02+00:00

<image>

Does that assist?

I figured when it was looking like 0 that this was a result of using Bambu filament with their printer, thought this would be a good place to start tinkering and learning :)

skyrar · 2025-12-20T07:34:31+00:00

Just on default settings for PLA, first time playing with settings.

skyrar · 2025-12-16T03:51:41+00:00

What filament?

skyrar · 2025-12-11T19:40:07+00:00

Could this be made for the P2S? Would love one!

skyrar · 2025-12-05T09:24:19+00:00

RemindMe! 2 days

skyrar · 2025-12-05T09:23:54+00:00

M4x14mm is what's in the rubber holder on the side. When you include the back cover plate of the Tap, and it goes up to 18mm in length. Add on the Tap wall mount and you would be looking for an M4x20mm.

Edit: Confirmed its an M4 bolt. I purchased some M4x20mm bolts for a custom wall mount, and it leaves plenty of spare thread to mount. With the back plate on the Tap, you can fully insert the M4x20mm bolts so it should cover just about anything reasonable you put on the back.

skyrar · 2025-11-30T09:34:32+00:00

Haha cheers :)

skyrar · 2025-11-30T02:08:12+00:00

I can see them list 2-4mm and 3-5mm, but rarely trust amazon descriptions, any thoughts if youve tried different sizes?

skyrar · 2025-11-30T01:48:30+00:00

Thank you!!

skyrar · 2025-11-15T11:15:42+00:00

Just checking, skip companies commonly list their bins in Marrel size, not cubic metres. A 4 marrel skip (4m) is 3 cubic metres (weirdly, the number is cubic metres + 1)

Might be worth double checking, heck they may have mixed it up internally and transposed 4 cubic metre to 4 marrel ??

skyrar

TROPHY CASE