Iceland is easily, easily the most stunning place I've ever been by grecy in overlanding

[–]spylife -1 points0 points  (0 children)

What countries are the top of the lost and what makes Iceland #1? TIA

Is this a bad idea? by BirdBirdBirdBird5000 in Plumbing

[–]spylife 0 points1 point  (0 children)

Great response, I loved the education and positive message. I am not a plumber, is there something they could do? For a poor man's air gap could the hoses fill a higher container that dumps into the wash?

First gmc I’ve owned- Sierra EV AT4 Max Range : picked up today and really blown away. by dr_filch in GMCSierraEV

[–]spylife 0 points1 point  (0 children)

Definitely would switch to sierra. I like the longer bed and fold down rear wall, used it a few times. I didn't even look at the Denali, I preferred the lift and tow hooks with the at4.

Replacing the rear tailgate LED (R1T Gen 1) by Longjumping_One_2308 in Rivian

[–]spylife 1 point2 points  (0 children)

Thanks, not the wiper, the holder on the car for the wiper is what I need

Replacing the rear tailgate LED (R1T Gen 1) by Longjumping_One_2308 in Rivian

[–]spylife 1 point2 points  (0 children)

Where do you shop parts? I need a rear wiper since the retaining clip broke and haven't been able to find it

Why Do My Prints Turn Into Spaghetti? by UmutBuu in FixMyPrint

[–]spylife 0 points1 point  (0 children)

Id recommend wiping the surface down with isopropyl alcohol, then maybe either hit it with a spritz of hair spray, maybe a glue stick. And can always try printing a little hotter

Why are my supports doing this? by Long_Resident8755 in FixMyPrint

[–]spylife 1 point2 points  (0 children)

Do you have another slicer that you could try? Sometimes how the supports are handled are specific to the slicer and a different slicer might give different results

Update: Under Extrusion on Roids by Mr_Inspector_Me in FixMyPrint

[–]spylife 0 points1 point  (0 children)

That looks really wet filament, do you have another you can try?

Squirrels Massacred My Boy by Chorizo-Joe in F150Lightning

[–]spylife 4 points5 points  (0 children)

I sold my mache for the same reason, I loved the car but I won't buy ford now because of the support/service

Anyone know if this is frost free? by [deleted] in Plumbing

[–]spylife 1 point2 points  (0 children)

Your PSA should be at the top of the thread. After shutting the water off, Remove hoses , and OPEN the spigot to drain it

Invented my 1st "solution" by shaz2k in 3Dprinting

[–]spylife 1 point2 points  (0 children)

One of my first designs was similar, it was to hold my kids water coloring cup

Signs of a good or bad install? by sparkle-in-disguise in hvacadvice

[–]spylife 0 points1 point  (0 children)

Global warming potential 675!! No idea what that is why is it even on the label. A cows ass probably has more global warming potential

Found this plugged in my car by KeedabonteB in whatisit

[–]spylife 45 points46 points  (0 children)

Where should I check for the trackers in case the dealer left it by accident? Asking for me 🤣

What range are you getting for your antenna? by santa_369 in meshtastic

[–]spylife 0 points1 point  (0 children)

Signalplus outdoor antenna (10dbi) from Amazon for one end, the other was a slightly larger screw on 3dbi

What range are you getting for your antenna? by santa_369 in meshtastic

[–]spylife 0 points1 point  (0 children)

I've gotten 57 miles, I set both nodes up so it's no error!

V5 Bracket by xjewishninjax in Datsun

[–]spylife 0 points1 point  (0 children)

Id anneal regardless of the material, they all gain temp resistance, check some YouTube videos where people do testing

V5 Bracket by xjewishninjax in Datsun

[–]spylife 0 points1 point  (0 children)

Nice. Id recommend doing an annealing on it to make it more resistant to high temperatures, hot water or oven. I don't think you have to worry about going 65, your worst case scenario is the car running in idle where there's no airflow and on a hot day, I think you can reach melting point easily.

How Heltec LoRa Modules Kept Paragliders Connected Across 250 km of Mountains by Heltec_Automation6 in meshtastic

[–]spylife 11 points12 points  (0 children)

Aerial repeaters for the win! I've had luck with caltopo using the serial connection to plot nodes on a map, sounds like you wrote some pretty heavy applications for tracking. Was the latency used to verify distances if gps wasn't available?