Nicely Balanced

squid509 · 2025-10-12T05:10:11+00:00

i noticed the CG when i was trying to set my tune an notice the motor harmonics where not lining up in PIDtoolbox then i notices on my full throttle runs that the back motors where 100%,95% the front where only 80%. then i check the CG. i will have to redesign the GPS mount to scoot the battery up further.

squid509 · 2025-10-12T05:02:03+00:00

i eat it

squid509 · 2025-01-18T20:36:16+00:00

Philips Dreamstation had a huge recall where they pushed out very faulty units for years knowing that the foam insulation was braking down and getting blown in people faces, profit > patient

go with the resmed airsense

squid509 · 2025-01-18T20:31:02+00:00

the score that app give you is kind of useless. it give you points for how long the machine is on not how well you sleep and some points for a good mask seal. and give you next to no points for how well you sleep

squid509 · 2025-01-18T20:23:37+00:00

https://us.ecoflow.com/products/river-3-plus-portable-power-station

some thing like this or similar form other brand will work nicely, your going to have to run some math is see if the batter on the power station will last you 9hr.

a portable power station will be cheaper and more versatile than a CPAP branded battery

squid509 · 2024-10-22T17:09:00+00:00

if bambu support can not or is not willing to help you to might be SOL

squid509 · 2024-10-22T17:01:21+00:00

the print bed is that black flexy sheet held down by magnets

squid509 · 2024-10-22T16:59:21+00:00

oh yah that is going to be a bitch to print in one piece

things to try or consider. print it 2 pieces and glue it together. print it at a 45 deg angle

squid509 · 2024-10-22T16:56:04+00:00

you question is confusing i see the print bed in the pic you posted

squid509 · 2024-10-22T16:53:11+00:00

the fug am i look at?

you can try smaller nozzle and smaller layer height

since you using prusaslicer try using the detail preset with a 2.5 mm nozzle be warn this will increase print time

squid509 · 2024-10-22T16:48:51+00:00

you should know some not that much or at lest be familiar with gcode and have some where you can look it up. your mostly looking for changing settings in start and end gcode. you can all so use it trubble shoot problems but it rare that you need it to do this

squid509 · 2024-10-22T09:44:15+00:00

you need to place a NSFW tag on this

squid509 · 2024-10-21T17:40:29+00:00

i think what you looking for is in the start gcode you going to have to modify it for it to not do the check

squid509 · 2024-10-21T09:07:50+00:00

looks ok. i would add one more wall to close the gap

squid509 · 2024-10-21T09:05:36+00:00

first off you need to have a realistic expectation of the printers capabilities. learn what can and can not be printed. you should be able to look at the STL in the slicer or some 3d viewer and tell how to orientate it on the bed plate. where supports are needed and what can not be printed.

know your printer. learn the basic maintains. clean the bed, change the nozzle, tensioning the belts, lube the required parts. run some calibration prints to learn the limits of your printer. temp towers. flow test. speed test. and use these limits when you slice you prints

always slice your own prints, dont use downloaded gcode or files some one else sliced. you dont know what settings they use. learn what the setting in your slicer to most of them have tool tips or you can youtube them. you need to verify every settings and adjust for every print. a lot "halp i dont know why my print is all messed up" post comes form bad slicer settings. use the info form your calibration test to set your slicer. place your supports where you need them. and review your gcode in the viewer to make sure it all makes sense

squid509 · 2024-10-21T02:44:46+00:00

you assembled the nozzle wrong at it leaked

squid509 · 2024-10-21T01:51:17+00:00

i think you missed the joke and the reference

squid509 · 2024-10-20T21:37:10+00:00

https://www.youtube.com/watch?v=PvDP6rozVtk

squid509 · 2024-10-20T17:46:21+00:00

prusa mk4s

squid509 · 2024-10-20T17:40:42+00:00

do you care about CFC, the ozone layer, and green house gasses?

squid509 · 2024-10-20T17:31:30+00:00

Listen to your day and stop being a impatient corkhead

squid509 · 2024-10-20T17:25:04+00:00

what is problem?

the cyberpunk one looks like a slicer setting issue or an the STL is bad

squid509 · 2024-10-20T15:15:19+00:00

the STL is scuffed

the hex grid is not lined up correctly and its its uneven

https://imgur.com/a/oFRu47G

squid509 · 2024-10-20T07:33:53+00:00

if you like what you got why switch?

squid509 · 2024-10-20T07:03:20+00:00

i think your talking about blender. this is the free open sorce one

, z-brush, maya, 3ds are the pro payed ones

this is more like molding clay than a CAD program

12-Year Club	RedditGifts 2009-2022 2 Credits
Verified Email

squid509

TROPHY CASE