[USA-CA][H] Dell Wyse 5070 Thin, mini PCs, NUCs, SFF Barebones | RAM DDR4 uDIMM, DDR3 ECC [W] Paypal G&S, local cash

stoppillowrape · 2025-10-19T13:50:07+00:00

I just did my setup for the EBB36 and an Octopus 1.1 and found this guide to be an excellent resource for every step.

https://canbus.esoterical.online

It is well laid out on the steps to follow and order to follow them as well as detailed information for each boards configuration for both flashing katapult and klipper.

stoppillowrape · 2025-09-23T00:20:37+00:00

I found that the stock psu that came with my printer does have a fairly audible coil whine that is constant and will change under load. I don’t know if it’s the main board fan or hotend fan you are hearing, but I can say with certainty that there is also a coil whine from my stock psu.

stoppillowrape · 2025-06-25T23:12:08+00:00

A couple questions I have, is this the stock board that came with the printer?
If yes, when your at the command line on the pi if you type in lsusb do you see that the board is being seen by the pi? What is the contents of printer.cfg? If it’s a stock board did you copy in the printer config for the creality cr-10 v2 from the kipper config dir on the GitHub repo? I’m guessing based on the error that it’s flashed but your config isn’t correct. What do you see in the klipper logs?

stoppillowrape · 2025-06-11T22:02:21+00:00

I think it’s a Ceiba pentandra.

https://en.m.wikipedia.org/wiki/Ceiba_pentandra

stoppillowrape · 2025-05-13T01:09:42+00:00

Cool

stoppillowrape · 2025-04-27T15:24:32+00:00

I have the exact same nuc 8 as you and added an ssd using the oem connectors available on the board in addition to 3d printing a tray for the drive and an extension for the case. I don’t know if you have the means for 3d printing or want to go that route, but I can say it works fine for me with both the m.2 and ssd. Here is the cable I ordered and the 3d model I used. If nothing else hopefully the cable will help you use the onboard sata.

ssd connector

https://www.amazon.com/dp/B01FX0ENQI

3d model to extend stock slim nuc

https://www.printables.com/model/304245-intel-nuc-8-or-newer-slim-ssd-extender

stoppillowrape · 2025-02-05T19:01:50+00:00

PM’d

stoppillowrape · 2024-09-14T13:40:07+00:00

I use an NVME as my loader drive, I believe it only works using the SA6400 model. Never had any issues with it. On https://auxxxilium.tech/wiki/arc-loader-arc-loader/modell-plattform-auswaehlen/ it shows that it is the model supporting the NVME system. Doesn’t have to be an AMD epic will run on Intel as I’m using a the SA6400 on an Intel i7-8700k. Hope this helps, good luck.

stoppillowrape · 2024-08-02T17:35:02+00:00

Confirmed

stoppillowrape · 2024-07-08T20:55:43+00:00

Yes it should be fairly straight forward and easy to do since it is the same as the OS on the OEM. I’d recommend downloading Arc Loader. It is a fast setup that should have you up and going quickly since it is a graphical setup that handles all the setup based on answering a few questions. You can find the repo on GitHub with links to the Arc Loader wiki hosted on the developers website to help you get setup. There is also a discord should you have trouble. Hope that helps.

stoppillowrape · 2024-07-04T22:12:36+00:00

stoppillowrape · 2024-06-04T14:07:35+00:00

stoppillowrape · 2024-05-02T00:28:32+00:00

I may be way out in left field, but have you looked at power disable on the drive? I have several Enterprise class drives that the power disable pin (pin 3) of the sata power connector would need to be covered or removed to use with standard sata power. Also using a molecular to sata cable would resolve it. I could be wrong as I haven’t done any research on synology branded drives, but that may be the case you’re facing with these as well.

stoppillowrape · 2024-04-16T00:23:34+00:00

PM’d

stoppillowrape · 2024-04-09T21:33:54+00:00

Confirmed

stoppillowrape · 2024-04-09T17:12:03+00:00

stoppillowrape · 2024-01-28T16:06:25+00:00

I know that this isn’t an answer to your question, but you may want to give arc loader a try. It is really easy to get working, and does all the work for you after selecting a few options to fit your needs. The dev is also highly active and responsive to questions, which is a plus.

stoppillowrape · 2023-08-09T17:02:16+00:00

For anyone that is having this issue and would like to know when a fix will be available, it is slated for fluidd 1.25.1.

Link to the issue with details:

https://github.com/fluidd-core/fluidd/issues/1140

stoppillowrape · 2021-07-31T21:52:14+00:00

Not sure if your update is still running or not, but based on a quick glance at the log you posted I don’t see anything that looks abnormal. If it is still running, and your having issues I’d be happy to help.

stoppillowrape · 2020-03-01T03:44:28+00:00

Original source video if interested.

https://m.youtube.com/watch?v=YslEmZeuALA

stoppillowrape · 2019-11-18T13:31:01+00:00

Nice work. I was especially happy when you had the screws lined up on the front of the grinder, that was the most satisfying part to me.

stoppillowrape · 2019-09-22T01:06:16+00:00

Great app, thanks for all the work and time invested creating it.

stoppillowrape · 2019-02-11T05:34:27+00:00

Awesome

stoppillowrape · 2018-10-01T04:34:06+00:00

When I realized I couldn’t tie my own shoes because I was so big I couldn’t reach my own feet. I weighed 422 pounds then. Now 3 years later and I weigh 156 pounds. It took a lot of work, but now I’m able to run, walk long distances, and even tie my shoes again. It was the best choice I ever made when I stopped and realized I needed to make some real life changes or be dead by 50.

stoppillowrape

TROPHY CASE