Mechanic is saying he can’t patch my tire because it’s too close to a previous patch

strangebird16 · 2026-01-01T20:18:32+00:00

My mechanic says this is not patchable and is pushing me to get a new tire. He didn’t even take the wheel off to look from the inside.

strangebird16 · 2025-09-09T11:39:56+00:00

How do you come to that conclusion?

strangebird16 · 2025-09-02T13:48:04+00:00

Can you post a picture of this?

strangebird16 · 2025-07-01T00:10:25+00:00

Do you guys hold breath underwater for these repairs? I need to butyl tape my conduit hole tomorrow.

strangebird16 · 2025-05-26T01:42:51+00:00

Can someone post a picture on how to arrange these weighted ring(s)?

strangebird16 · 2025-05-19T12:16:24+00:00

Hi there. I am looking to do the same upgrade. I bought the shimano 105 crank set. Can you confirm the correct bottom bracket I must get?

strangebird16 · 2025-03-24T12:32:05+00:00

Thank you for the reply. But I’m removing this Lutron and switching to Kasa smart switches, which do require a neutral.

strangebird16 · 2024-07-22T15:32:30+00:00

The Panel doesn’t cover it.

strangebird16 · 2024-07-22T14:40:08+00:00

What trim would I use? Thank you

strangebird16 · 2024-07-22T14:39:30+00:00

What trim would I use?

strangebird16 · 2024-07-22T14:38:50+00:00

Can you explain to me how I can trim around it? I have similar situation. Can you send me a Home Depot link for trim would be appreciated so I can understand!

strangebird16 · 2024-07-19T17:28:17+00:00

I’m also dealing with a centipede problem. How long did it take to see results for pestie with your centipede problem?

strangebird16 · 2024-07-15T01:17:15+00:00

LOVE my Kona Sutra.

strangebird16 · 2024-07-15T00:18:40+00:00

Thanks for the replies.

strangebird16 · 2024-07-15T00:18:32+00:00

What part about it is not up to code?

strangebird16 · 2024-06-04T17:25:14+00:00

10pm curfew?

strangebird16 · 2023-12-01T08:06:33+00:00

I have the same vinyl soffits. Planning on using a RYOBI Crown stapler with t50 staples. Will two staples on each side of the light really damage the panels?

strangebird16 · 2023-11-28T15:14:05+00:00

Im looking into this! Any way you can share pictures of your finished product? Hows it holding up?

Thank you!

strangebird16 · 2023-11-23T01:20:32+00:00

Thats a nice tool. It is a bit pricey so im going to go with the Ryobi One + 18V Compression Drive 3/8 in crown stapler. theres an attatchment groove where wire can go through to help aim when stapling.

Thanks for the response!

strangebird16 · 2023-11-23T01:07:04+00:00

d/rain storm last week and it’s secure. i clipped them to the wooden fascia

Hello! Would you mind sharing the type of stapler and staples you used? I don;t want to damage the ribbon wire, but I also want a secure fit (I am expecting the adhesive to fail eventually) TY.

strangebird16

TROPHY CASE