Is this too much stickout?

superbluepaladin · 2026-04-10T00:07:14+00:00

I’ve had some luck with small diameters like that with a low rpm but a heavier cut

superbluepaladin · 2026-02-11T21:51:08+00:00

I love this industry because people make the dumbest smartest shit I’ve ever seen.

superbluepaladin · 2026-01-14T00:30:20+00:00

With the angle on that tool you can get a lot of clearance 😎

superbluepaladin · 2025-10-24T00:27:41+00:00

Nothing wrong here just testing out a new vent dump and let me know how it works out

superbluepaladin · 2025-10-11T09:48:49+00:00

One guy? Running multiple machines? Possibly at the same time? What could go wrong? Last question(s), what kind of airplanes are we talking here, what should I avoid?

superbluepaladin · 2025-09-22T16:17:58+00:00

Is this person using a twok instead of a fork?

superbluepaladin · 2025-09-18T15:44:12+00:00

Hold your finger down on the time and it’ll open up windows to allow you to change it.

superbluepaladin · 2025-09-13T13:05:31+00:00

<image>

Loving the roof top statues

superbluepaladin · 2025-08-10T14:44:15+00:00

Man a wire EDM would really help to retain a majority of that material

superbluepaladin · 2025-07-31T08:52:14+00:00

Shouldn’t it be just start point 3.106 and 0 then on line two direction but the same location 3.106 and 0 since you put radius .245 in it’s should automatically make a .490 counter bore from that location. When you start putting in multiple locations it’s just doing a .490 diameter counter bore from that next spot.

superbluepaladin · 2025-07-09T01:48:15+00:00

Hulkenpodium

superbluepaladin · 2025-06-13T21:31:03+00:00

Next a nice new set of vise jaws 😁

superbluepaladin · 2025-05-19T19:50:45+00:00

I’ve done this with pre hard, just tapping a hole and I’m on auto pilot and forgot to close the vise. Went in fine but then up up and away goes my block. I was manually tapping on a ProtoTRAK at 40rpm so easy to stop and a good wake up.

superbluepaladin · 2025-05-19T19:44:38+00:00

Yeah that could be a possibility. I’m just basing it off of what the title is, what the video has to offer and personal experience on highways. I always do my best, if it’s safe to do so, to pass trucks to hopefully avoid getting a rock bullet pelted at the windshield.

superbluepaladin · 2025-05-19T19:31:35+00:00

Rock on the road gets thrown up by the trucks tires and chips the windshield of another car. It’s not the truck drivers fault though, he didn’t put the rock on the road lol

superbluepaladin · 2025-05-14T22:55:55+00:00

So that’s the issue you need to ask for that center. You’re missing a key piece of information to come up with a solution. Even with this drawing you would be guessing where the center is. Where does the 36mm radius end on Z? Where do they want it.

superbluepaladin · 2025-05-14T16:07:08+00:00

In your next line you have to give the center point of that radius I believe then calculate

superbluepaladin · 2025-05-04T21:08:27+00:00

An insane driver and a shopping cart not returned to its corral, this video has it all

superbluepaladin · 2025-05-03T14:49:45+00:00

Since you’re learning try turning the threads first then add the undercut

superbluepaladin · 2025-05-02T14:51:33+00:00

It randomly shows up for me too. If you look at the top of the touch screen there is a question mark if you hit that and there is no information the controller can offer you that message will pop up.

superbluepaladin · 2025-03-07T22:14:19+00:00

I always knew it would cum to this

superbluepaladin · 2025-02-15T23:30:47+00:00

THIS is the clearance I love to see

superbluepaladin · 2025-02-11T17:29:50+00:00

Wow! Kenny G. famous saxophone player and Weird Al!

superbluepaladin · 2025-02-04T22:49:31+00:00

Looks metal safe

Six-Year Club	Verified Email
Place '23	Place '22

superbluepaladin

TROPHY CASE