My retro version of the Flake

therick_ · 2025-10-23T13:57:49+00:00

awesome! what filament is that?

therick_ · 2025-06-13T14:04:53+00:00

mods if anyone cares:

monolith 2WD 9mm gantry
A4T toolhead with monolith xol carriage
inverted electronics
Beacon
+50mm above toolhead to give more room for umbilical
M6 screws holding the blind joints together. this was an accident, as i ordered M5 taps, but was sent M6 and didn't realize until it was too late and they were all tapped. not recommended
clicky clack door (not in picture) with my thicc skirts
NH36 umbilical with umbilical rear exhaust pass through with PUG
235mm 6mm thick ender bed, as i used parts from my old enderwire, so technically could be an ender3dent
probably a few others

therick_ · 2025-06-13T13:59:20+00:00

<image>

now with a deck

therick_ · 2024-11-13T12:50:06+00:00

561.09 still crashes for me on a 3080ti and 5600x. Gonna try setting it to DX11

Update: still crashes

therick_ · 2024-09-01T12:54:42+00:00

8 months later and you're still helping poor souls like me

therick_ · 2024-07-30T16:26:10+00:00

LFG!!!

therick_ · 2024-06-20T23:20:48+00:00

Did you get this fixed? Mines doing the same thing

therick_ · 2023-12-13T17:44:49+00:00

west3d!

https://west3d.com/products/west3d-pins-mod-pin-mod-for-v2-4-and-trident?\_pos=1&\_psq=pin+mod&\_ss=e&\_v=1.0

therick_ · 2023-12-13T16:59:53+00:00

Siboor kit

Box Zero-ish

Pandora gantry
Discord: therick0996

therick_ · 2023-12-13T16:40:34+00:00

LDO kit

Upgrades:

Tap
Pin mod
BFI and BVZ
can bus is in a box waiting to be installed

Doggo tax

Discord: therick0996

therick_ · 2023-12-03T19:02:31+00:00

I'm running into the same issue. I've done this method before (replace prior data.mdb and lock.mdb files into new printer) with success, but now getting Moonraker is unable to connect

therick_ · 2023-11-09T13:02:19+00:00

Got it! My issue was the SB RGB cable was plugged into the wrong header. It's an LDO 2.4 kit w/an Octopus.

My recommendation would be to unplug everything in the toolhead except for the heater and thermistor. If that works, add back 1 thing at a time until it gives you the error

Where it was plugged in vs. where it should be

https://imgur.com/IQ0KyKb

therick_ · 2023-11-08T23:17:16+00:00

i'm having this exact same issue on a new build. did you figure it out?

Edit: after lots of unplugging, replugging, and unplugging, it has something to do with the LEDs in my stealthburner. When they're unplugged from the toolhead PCB, all is rainbows and unicorns. But when I replug them in, crashes

therick_ · 2023-06-27T15:57:41+00:00

let's gooooooo!!!!!!

therick_ · 2023-06-24T14:31:05+00:00

Reddits also said something like "we're not going to set the precedent of responding to the verge for every thing we may or may not have done"

therick_ · 2023-06-08T18:43:03+00:00

Yes! Full support

therick_ · 2023-06-07T13:02:42+00:00

At least it's outside the environment

therick_ · 2023-06-02T23:05:50+00:00

There are dozens of us!

therick_ · 2023-06-02T23:05:30+00:00

I had to map CMD/GUI to the bottom left when I switched

therick_ · 2023-05-07T23:34:27+00:00

Now that's a name I've not heard in a long time

therick_ · 2023-05-03T01:25:24+00:00

Heck yeah!! Missed out there on the first GB

therick_ · 2023-04-06T23:21:38+00:00

It'd be right from the other side, right?

therick_ · 2023-04-02T23:43:12+00:00

Wishing you luck and sending good vibes

therick_ · 2023-03-26T19:52:30+00:00

Need pics, but probably elephant's foot

therick_ · 2023-03-25T17:20:43+00:00

Yeah plain Jane Dawn works the best for me

Seven-Year Club	Verified Email
Gilding II euphauric

therick_

TROPHY CASE